Publicidad
Idiomas disponibles
Idiomas disponibles
FIG. 1
2"
(51 mm)
TRACING NON-PAIRED WIRES (FIG. 2)
1. Connect the Digital Toner-Pro's red
Connect the Digital Toner-Pro's red
respective Test Lead Inputs
2. Connect the Digital Toner-Pro's red ABN Test Clip
3. Connect the black ABN Test Clip
not in the same pair (connect to ground, if available). When tracing a shielded
not in the same pair (connect to ground, if available). When tracing a shielded
not in the same pair (connect to ground, if available). When tracing a shielded
not in the same pair (connect to ground, if available). When tracing a shielded
not in the same pair (connect to ground, if available). When tracing a shielded
cable, connect the red ABN Test Clip to the outer shield, and the black ABN
cable, connect the red ABN Test Clip to the outer shield, and the black ABN
cable, connect the red ABN Test Clip to the outer shield, and the black ABN
cable, connect the red ABN Test Clip to the outer shield, and the black ABN
Test Clip to the center conductor or ground.
Test Clip to the center conductor or ground.
4. Turn Digital Toner-Pro on by pressing the Power On/Off button
5. The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
, and Wire Map Indicator
T13 T13 T13
may be blinking, depending on whether the Toner is connected to a
may be blinking, depending on whether the Toner is connected to a
network port. The "CONT" Indicator
in analog mode. When performing analog toning, check the "CONT"
in analog mode.
Indicator
T4
NOTE: When performing Digital Toning, the "CONT" Indicator
not illuminate.
6. Turn the Digital Probe-Pro on by pressing the Power On/Off button
7. Select the preferred tone setting using the Digital/Analog Tone Button
8. At the far end of the cable, spread the wires at least 2" (51 mm) apart, if possible.
9. If performing analog toning, first ensure the Digital Toner-Pro is set to analog
toning mode. Then ensure the Digital Probe-Pro is set to analog mode by
toning mode. Then ensure the Digital Probe-Pro is set to analog mode by
pressing the Analog Mode button
green when in analog mode. If performing digital toning, first ensure the
Digital Toner-Pro is set to digital toning mode. Then ensure the Digital Probe-
Digital Toner-Pro is set to digital toning mode. Then ensure the Digital Probe-
Pro is set to digital mode by pressing the Digital Mode Button
Mode Button will illuminate blue when in digital mode.
10. Use the Digital Probe-Pro to scan the cable's wire pairs. Move the Digital Probe-
Use the Digital Probe-Pro to scan the cable's wire pairs. Move the Digital Probe-
Pro's tip
slowly across the wires (FIG. 2). The Digital Probe-Pro's volume
slowly across the wires (FIG. 2). The Digital Probe-Pro's volume
slowly across the wires (FIG. 2). The Digital Probe-Pro's volume
slowly across the wires (FIG. 2). The Digital Probe-Pro's volume
P1
and Signal Strength Indicator bars
toned pair. When the Digital Probe-Pro's volume and Signal Strength Indicator
bars are high over the first wire, low in the middle (between) the two wires, and
high over the second wire, you have located the pair of wires you are tracing. Use
high over the second wire, you have located the pair of wires you are tracing. Use
high over the second wire, you have located the pair of wires you are tracing. Use
the Volume Increase
OPERATING INSTRUCTIONS
T20 T20 T20
When performing analog toning, check the "CONT"
When performing analog toning, check the "CONT"
When performing analog toning, check the "CONT"
. If illuminated green, you may proceed.
and Volume Decrease
and
P6
and black
T14 T14
T15 T15
to another wire in the cable, but preferably
to another wire in the cable, but preferably
T15 T15
LEDs 3 and 6 illuminated. The LEDs
LEDs 3 and 6 illuminated. The LEDs
T18 T18 T18 T18 T18
illuminates green or red only when
illuminates green or red only when
illuminates green or red only when
illuminates green or red only when
T4
. The Analog Mode Button will illuminate
P12 P12 P12
+ +
will increase as it approaches the
will increase as it approaches the
P4
P5
P7
ABN Test Clip leads to their
ABN Test Clip leads to their
to the wire to be traced.
to the wire to be traced.
T14 T14
.
T9
. The Digital
P11 P11
buttons to adjust the volume.
buttons to adjust the volume.
will
T4
.
P3
.
T7 T7
7
Publicidad
