Maytag Commercial MAT24PD Instrucciones página 10

A 220 V–240 V, 50 Hz AC only, 10 A, fused electric supply is
n
required. A time-delay fuse or circuit breaker is recommended.
It is recommended that a separate circuit serving only this
appliance be provided.
A detachable 3 conductor, 250 V, 10 A, 1.0 mm2 (18 AWG)
n
minimum, power supply cord, 1,800 mm (6 ft) long (minimum),
with one end terminated with an IEC 60320-1 C13 connector,
the other end terminated in an IEC type I, G, E, or F Plug Type,
earthing-type plug meeting the local, national, and/or regional
approval authority/safety agency standards is required.
Approved Maytag power supply cords are available for order
for specific regions per the Power Cord Selection table.
To minimize possible shock hazard, the cord must be plugged
n
into a mating, earthing-type outlet, earthed in accordance with
local codes and ordinances. If a mating outlet is not available,
it is the personal responsibility and obligation of the customer
to have the properly earthed outlet installed by a qualified
electrician.
If codes permit and a separate ground wire is used, it is
n
recommended that a qualified electrician determine that the
earth path is adequate.
If the supply cord is damaged, it must be replaced by a
n
special cord or assembly available from the manufacturer or
its service agent.
Do not earth to a gas pipe.
n
Check with a qualified electrician if you are not sure the
n
washer is properly earthed.
Do not have a fuse in the neutral or earth circuit.
n
Only a Maytag service person, qualified electrician, or similarly
n
qualified person shall replace a power cord or perform service
on the electrical power supply in accordance with these
instructions and local codes and regulations.
This product is shipped with the AS/NZS 3112 power cord
n
installed. Additional power cords are supplied with the
product. Refer to the Power Cord Selection table to determine
the power cord required for your region, or if needed, to order
the appropriate approved Maytag power supply cord.
After installation, access to mains plug must be ensured at all
n
times in order to ensure immediate deactivation of the washer
in case of emergency.
The appliance inlet, power supply cord, and retainer
n
bracket must remain fully assembled and connected. If any
component becomes damaged and/or disconnected, the
appliance must be unplugged and the damaged component
must be replaced by the manufacturer, its service agent, or
similarly qualified persons in order to avoid a hazard.
IMPORTANT: Washer installation and service must be performed
by a Maytag authorized service person.
EARTHING INSTRUCTIONS
This washer must be earthed. In the event of a malfunction
or breakdown, earthing will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-earthing conductor and an earthing plug. The
plug must be plugged into an appropriate outlet that is
properly installed and earthed in accordance with all local
codes and ordinances.
WARNING:
Improper connection of the equipment-
earthing conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly earthed.
Do not modify the plug provided with the appliance – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
10
NOTE: Electrical safety standards: The manufacturer has
chosen compliance with IEC/EN.60335 standards as the most
appropriate for this product.
n Sound Pressure Level, LpA: 58 dbA (uncertainty, kPa: +/-3.6 dbA).
POWER CORD SELECTION
Part Number IEC Plug Type*
W11318406
(fused 13A)
(Included in product)
W11318407 E, F Suhuko
(Included in product)
W11318408
(Installed on product
as shipped)
*- https://www.iec.ch/worldplugs/
INSTALLATION INSTRUCTIONS
WARNING
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
1. Move washer to within 4 ft (1.2 m) of its final location; it must
be in a fully upright position.
NOTE: To avoid floor damage, set washer onto cardboard
before moving it and make sure lid is taped shut.
1.2 m
(48")
Intended
Counties/Region
United Kingdom,
Ireland, Cyprus,
Malaysia, Malta,
Nigeria, Singapore,
G
Hong Kong,
Saudi Arabia, UAE,
GCC states, others
(BS1363)
EU, Belgium, Chile,
Egypt, France,
Indonesia, Jordan,
Rep. of Korea,
(CEE 7/7) Paraguay, Russia,
Thailand, Uruguay,
Ukraine, Vietnam,
others
Australia, China, New
Zealand, Papua New
I
Guinea (AS/NZS
3112)