Maytag Commercial MAT24PD Instrucciones página 16

IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished, but
failure may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to
n
green ground connection point or unpainted metal in the
washer.
Touch your finger repeatedly to a green earth connection
point or unpainted metal in the washer.
Before removing the part from its package, touch the
n
anti-static bag to a green earth connection point or
unpainted metal in the washer.
Avoid touching electronic parts or terminal contacts; han-
n
dle electronic control assembly by edges only.
When repackaging failed electronic control assembly in
n
anti-static bag, observe above instructions.
GENERAL INFORMATION
Blank Display
Check power to machine. Enter Service Mode and check for
Fault Code.
"0 Minutes" showing in display
This indicates the previous cycle is complete or a machine reset
was performed. Opening the lid will restore the display to the
Vend Price or Available state.
Factory Default Settings
Washer is programmed at the factory as follows:
POWERWASH = Hot Water Main Wash - Deep Rinse - Heavy
n
Soil Option Enabled- Extra Rinse Option Enabled - COIN
model pricing set to $2.50.
NORMAL = Warm Water Main Wash - Deep Rinse - No
n
Options Enabled - COIN model pricing set to $2.00.
DELICATES = Cold Water Main Wash - Deep Rinse - No
n
Options Enabled - COIN model pricing set to $1.75.
NORMAL ECO = Warm Water Main Wash - Progressive
n
Spray Rinse - No Options Enabled - COIN model pricing set
to $1.75.
Total calculated cycle price based on Base Cycle
n
Cost + Cost of Options Selected (Extra Rinse, Soil Level, and
Water Temperature). Default total cycle price dependent on
Cycle Settings selected. PowerWash cycle price will not re-
duce from programmed settings (Base Cycle Price + Cost of
Options Selected per Cycle Settings) when end-user makes
changes to selected cycle options (in example changes hot
water to cold water). All other cycle prices are calculated
based on final cycle selections made by the end-user.
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to
the portion of the cycle that existed at time of the power failure.
To continue the cycle, press START/PAUSE.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, "SELECT CYCLE" will appear and cycle price will show
"0.00."
16
-OR-
Display
After the washer has been installed and plugged in, the display
will show "SYnC" for a few seconds, then "0 MINUTES." Once
the washer has been plugged in and the washer lid opened and
closed, the display will show the price. In washers set for free
cycles, the display will flash "SELECT CYCLE," and will display
"PRICE 0.00."
CYCLES
POWERWASH
NORMAL
DELICATES
NORMAL
ECO
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
The top three keypads on the left side, the top keypad on the
right side, and the digital display are used to set up the controls.
The display can contain four numbers and/or letters and a
decimal point. These are used to indicate the set-up codes and
related code values available for use in programming the washer.
How to use the keypads to program the controls
1. The POWERWASH keypad is used to adjust the values
associated with set-up codes. Pressing the keypad will
increment the value.
Rapid adjustment is possible by holding the keypad down.
2. The NORMAL keypad will advance you through the
set-up codes. Pressing the keypad will advance you to
the next available set-up code. Holding the keypad down
will automatically advance through the set-up codes at a rate
of one (1) per second.
3. The DELICATES keypad is used to select or deselect options.
4. The TEMPERATURE keypad is used to decrease set-up code
value.
Start Operating Setup
PD Models: Insert access door key, turn, and lift to remove
n
access door.
PR models set for free vend: Refer to bottom of page for
n
operating setup.
IMPORTANT: The console must not be opened unless power
is first removed from the washer. To access connector J4:
g Unplug washer or disconnect power.
g Open console, disconnect plug on J4, close console.
g Plug in washer or reconnect power.
The washer is now in the set-up mode.
Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a unit that
operates.
Set-Up Codes
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE: Set-up codes marked with "*" are able to transfer from
one machine to another machine (must be same model type) via
USB stick.
OPTIONS
TEMPERATURE
SOIL LEVEL
EXTRA RINSE