Maytag Commercial MAT24PD Instrucciones página 19

Table 1
A3, A4, Extra Soil Level Water
A5, A6 Rinse (Heavy-On, Temp
Normal-Off)
00 Off Off Tap
Cold
01 Off Off Cold
02 Off Off Cool
03 Off Off Warm
04 Off Off Hot
08 Off On Tap
Cold
09 Off On Cold
a Off On Cool
B Off On Warm
C Off On Hot
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS.
2xxx Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the NORMAL keypad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number in THOUSANDS.
4xxx Number in ONES.
5 xx Number of HUNDRETHS.
CONTROLS SET-UP THROUGH USB
To access the USB setup menu, navigate to set-up code 2.xx
(special pricing option). Pressing POWERWASH keypad activates
the help mode sub-menu. The first sub-mode within the help
mode is USB option. Press POWERWASH keypad at any time to
exit help mode.
S d
UbmOde eSCRIpTION
USB While on this screen, press the
POWERWASH button to enter into USB
menu. USB menu allows for software
update and import/export machine
settings.
USB MENU
To access USB menu enter into Help Mode. While on the USB
screen press the POWERWASH key. To advance through the
USB sub menu, use the MIXED key. The DELICATES key is the
Select key. Press the POWERWASH keypad at any time to exit
USB Menu.
See Page 20 for location of the USB Port on the appliance and
instructions for how to install a USB Stick onto the appliance and
to remove a USB stick from the appliance.
A3, A4, Extra Soil Level Water
A5, A6 Rinse (Heavy-On, Temp
Normal-Off)
10 On Off Tap
Cold
11 On Off Cold
12 On Off Cool
13 On Off Warm
14 On Off Hot
18 On On Tap
Cold
19 On On Cold
1A On On Cool
1B On On Warm
1C On On Hot
1 02 = 2,000
2225 = 225
TOTAL CYCLES = 2,225
3 01 = $1,000.00
4600 = $ 600.00
5 75 = $ 00.75
TOTAL = $1,600.75
N
OTe
Allows user to enter
USB menu. See USB
MENU section for
more information.
CODE
U0.00 USB drive Inserted? (Status only)
U0.00 This will be displayed if USB drive is NOT detected.
U0.01 This will be displayed if USB drive is detected.
g Press the NORMAL keypad once to advance to next code.
U1.00 Programming Mode.
U1.00 This will be displayed if USB drive not detected.
U1.01 This will be displayed if USB drive is detected. If you wish to
reprogram the controls Press the DELICATES keypad 3 times.
Display will toggle between U1.01 and ProG while updating ACU
or U1.01 and --.-- while updating UI is in process. Please wait
until process is complete, this could take several minutes. After
software is successfully downloaded to machine, the control could
take several minutes to reset. After reset is complete the machine
will return to customer mode or service mode depending on
Service Switch status.
FCE4 or If the software programming was unsuccessful the display will
FCE5 toggle between U1.01 and FCE4 or FCE5.
g Press the NORMAL keypad once to advance to next code.
U2.00 Export Machine Settings to USB Drive.
U2.00 This will be displayed if USB drive is not detected.
U2.01 This will be displayed if USB drive is detected. If you wish to
export machine settings to USB drive press the DELICATES key
3 times. Display will toggle between U2.01 and --.-- while export
in process.
donE Display will toggle between U2.01 and donE when export finished
successfully.
FCE4 or If the export was unsuccessful the display will toggle between
FCE5 U2.01 and FCE4 or FCE5.
g Press the NORMAL keypad once to advance to next code.
U3.00 Import Machine Settings from USB Drive.
U3.00 This will be displayed if USB drive is not detected.
U3.01 This will be displayed if USB drive is detected. If you wish to
import machine settings from USB drive to machine press the
DELICATES key 3 times. Display will toggle between U3.01 and
--.-- while import in process.
donE Display will toggle between U3.01 and donE when import finished
successfully.
FCE4 or If the import was unsuccessful the display will toggle between
FCE5 U3.01 and FCE4 or FCE5.
g Press the NORMAL keypad once to advance to next code.
U4.00 Export Machine Audit Data to USB Drive.
U4.00 This will be displayed if USB drive is not detected.
U4.01 This will be displayed if USB drive is detected. If you wish to
export machine audit data to USB drive press the DELICATES key
3 times. Display will toggle between U4.01 and --.-- while export
in process.
donE Display will toggle between U4.01 and donE when export finished
successfully.
FCE4 or If the export was unsuccessful the display will toggle between
FCE5 U4.01 and FCE4 of FCE5.
EXPLANATION
19