Nilfisk 3707 Manual De Instrucciones página 36

3707 - 3707/10 - 3907 - 3907/18 - 3907W
Emptying of the liquid container
Before proceeding with these operations, turn off the
machine and remove the plug from the power socket.
Check the machine filtration class.
Before emptying the container it is advisable to clean the filter
(see "Cleaning the primary filter" paragraph).
■ Release the container (2) with the lever (3) and remove it,
then remove the liquid stop device and empty it.
■ Clean the machine as described in the "Maintenance,
cleaning and decontamination" paragraph.
■ Wash the container with clean water if aggressive
substances have been vacuumed.
■ Make sure the gasket is in perfect condition and correctly
positioned.
■ Place the container back in position and secure it again.
After the cleaning session, leave the machine running for at
least 60 seconds before turning it off.
Avoid switching on/off too frequently.
The filter element will be wet after liquids have been
vacuumed.
A wet filter element can quickly become clogged if the
machine is then used to vacuum dry substances.
For this reason, make sure that the filter element is dry or
replace it with another one before using the machine for dry
materials.
Dust Bag
The machine can be equipped with dust collection bag.
In this case, the machine must be equipped with optional
accessories (depressor and grid).
If the bag is not installed or is installed improperly, it could
create health risks for people exposed.
EN
Paper Bag and Safe Bag for dust collection
GB
The machine can be equipped with dust collection bag.
In this case, the machine must be equipped with a specific
container and a cap on the side.
If the bag is not properly installed, it could create health risks
for people exposed.
The safe bag system is suitable to collect toxic dust to
ensure that the user does not come into contact with the
product.
Longopac bag for dust collection
®
The machine can be equipped with dust collection bag.
In this case, the material is discharged by gravity when the
vacuuming stops. The Longopac® bag can be cut, sealed or
closed to the size required.
If the bag is not properly installed, it could create health risks
for people exposed.
C65
CAUTION!
Figure 1
[ NOTE ]
[ NOTE ]
Figure 9
Figure 10
[ NOTE ]
Figure 11
Dust bag replacement
■ Before proceeding with these operations, turn off
the machine and remove the plug from the power
socket.
■
These operations can only be carried out by trained
and qualified personnel who must wear adequate
clothing, in compliance with the laws in force.
■ In case of hazardous and/or harmful dust, use only
the bags recommended by the manufacturer (see
"Recommended spare parts").
■ The bag must only be disposed of by qualified
personnel and in compliance with the laws in force.
■
Use only original Nilfisk bags.
■
Only use bags suitable for the machine class you
are using.
Take care not to raise dust during this operation. Wear
a P3 mask and other protective clothing plus protective
gloves (PPE) suited to the hazardous nature of the dust
collected, refer to the laws in force.
How to replace the Dust Bag
■ Close the inlet by using the relevant cap (if equipped).
■ Release the dust container.
■ Remove the dust bag and close it with a clamp, if
necessary.
■ Place a new bag, taking care to wrap it around the outer
wall of the dust container.
■ Set the dust container into the machine again.
How to replace the Paper Bag
■ Close the inlet by using the relevant cap (if equipped).
■ Release the dust container.
■ Remove the bag and close it with the relevant cap (1) as
shown in the figure.
■ Insert a new bag, making sure the bag inlet is sealed.
■ Set the dust container into the machine again.
How to replace the Safe Bag
■ Remove and put the vacuum hose in a safe and dust-free
place.
■ Close the inlet by using the relevant cap (if equipped).
■ Release the dust container.
■ Close the Safe Bag by pulling the "guillotine" seal (2).
■ Close the plastic bag hermetically using the relevant band
(3).
■ Use the sticky tape (4) to close the bottom of the plastic
bag.
■ Remove the relevant connection (5) of the bag from the
vacuum inlet.
■ Insert a new safe bag, making sure the vacuum inlet is
well connected to the bag attachment, to grant the sealing.
■ Wrap the plastic bag around the dust container external
wall.
■ Place the dust container in the vacuum cleaner.
How to replace the Longopac® for machines that
handle dusts that are hazardous to health.
14
CAUTION!
CAUTION!
Figure 9
Figure 10
Figure 10