Setup Menu Table - Thermo Scientific Orion Star Manual Del Usuario

Meter Setup
Setup Menu Table –
Star Plus meters. Meters may not include all of the options listed in this table.
Top Line Middle Line
PH rES
PH bUF
ISE rES
ISE UnIt
ISE rAng
ISE nLIn
C0nd tC
C0nd C0EF
C0nd tdSF
C0nd CELL
C0nd trEF
C0nd tyPE
See the Setup Menu for RDO Optical Dissolved Oxygen Sensor section for details on the RDO sensor information menus.
d0 rES
d0 rES
d0 bAr
d0 PrES
d0 SAL
d0 SALF
d0 CALt
d0 LIFE
dUE PH
dUE 0rP
dUE ISE
dUE C0nd
dUE d0
EN-12
The following table is for the complete line of Orion Star and
Bottom Line
0.1, 0.01, 0.001
USA, EUr0
1, 2, 3
m, mgL, PEr, PPb, n0nE
L0w, HIgH
AUt0, 0FF
0FF, LIn, nLF
0.0 to 10.0
0.00 to 10.0
0.001 to 199.0
5, 10, 15, 20, 25
Std, 1, 2, 3, 4, 5, 6, 7, USP
0.1, 1 % sat
0.01, 0.1 mg/L
AUt0, mAn
450.0 to 850.0
AUt0, mAn
0 to 45
AIr, H20, mAn, SEt0
365 to 0
0 to 9999
0 to 9999
0 to 9999
0 to 9999
0 to 9999
Thermo Scientific Orion Star
Setup Menu Description (default setting, method specific)
pH measurement resolution (0.01, yes)
pH buffer set for automatic buffer recognition during calibration,
USA buffers are 1.68, 4.01, 7.00, 10.01, 12.46 and EUrO buffers are
1.68, 4.01, 6.86, 9.18 (USA, yes)
ISE measurement resolution in significant figures (1, yes)
ISE measurement units (PPb, yes)
ISE concentration range for calibration stability criteria (HIgH, yes)
ISE automatic blank correction for low-level calibration (AUt0, yes)
Conductivity temperature compensation type, LIn is for linear, nLF is
for non-linear pure water samples (LIn, yes)
Conductivity temperature compensation coefficient in % change in
conductivity per °C, appears if LIn was selected for tC (2.1, yes)
Conductivity TDS factor value (0.49, yes)
Conductivity default cell constant value for automatic conductivity
calibration mode (0.475, yes)
Conductivity reference temperature (25, yes)
Conductivity cell type and selectable range (Std, yes)
DO % saturation measurement resolution (0.1, yes)
DO mg/L measurement resolution (0.01, yes)
DO barometric pressure compensation type (AUt0, yes)
DO manual barometric pressure compensation value, appears if
mAn was selected for bAr (760.0, yes)
DO salinity correction type (AUt0, yes)
DO manual salinity correction value, appears if mAn was selected
for SAL or a DO meter without a conductivity mode is used (0, yes)
DO calibration type (AIr, yes)
RDO cap replacement countdown in days – 3, 4 and 5 Star Plus RDO
meters only (Set by RDO sensor, no)
pH calibration alarm value in hours, 0 is off (0, yes)
ORP calibration alarm value in hours, 0 is off (0, yes)
ISE calibration alarm value in hours, 0 is off (0, yes)
Conductivity calibration alarm value in hours, 0 is off (0, yes)
DO calibration alarm value in hours, 0 is off (0, yes)
and Star Plus Series Meter User Guide
™