Sammic HM-1035M Instrucciones página 18

To stop the oven
Open the oven door or press the
STOP/RESET button to stop the oven
operation. The screen continues to
show the countdown for the time set.
Close the door and press the
START/+30 SEC button to restart the
oven.
To cancel errors
If the oven does not cook, press the
STOP/RESET button to delete the
screen. If the oven cooks, press the
STOP/RESET button once so that the
oven stops, and then again to delete the
screen. If the oven door is open and the
time is displayed on the screen, close
the oven door and press the
STOP/RESET button to delete the
screen.
Does my oven have the
stage programming
option?
No button on the oven shows the stage
programming (it is a hidden function).
Stage cooking is a function that is
present during programming. Consult
the Programming buttons on this page
for more detail.
QTY 2X button
(some models)
To double the cooking time when cooking
more than one portion of food.
The maximum cooking time is 60 minutes
00 seconds, except when cooking at full
power. When full power (100%) is used, the
maximum cooking time is 20 minutes 00
seconds.
1. Open the oven door and put the food
in. Close the door.
• The screen displays: 0. The light will
switch on.
2. Press the QTY 2X button.
• The screen displays DOUBLE
3. Press the button or sequence of preset
buttons (e.g.: button 5)
• The screen displays PROG- 05
4. The oven will start to cook the food
after 1 second. The cooking time shown
on the screen is the sum of the original
cooking time doubled.
8
ENGLISH
How to use the oven electronic controls
Manual time input
To cook food for a specific time and at a specific power level of your choice.
NOTE: To use the Time Input, you must first press the POWER LEVEL button.
1. Open the oven door and put the food in. Close the door.
• The screen displays: 0. The light will switch on.
2. Press the POWER LEVEL button.
• If you want you can press the POWER LEVEL button to change
the power level (some models).
• The screen displays the power level (e.g.: 100%).
- 100% means 100% microwave power, 80% means 80%, 60%
means 60% and 40% means 40% microwave power. When you press the power
level button continuously, the power level will cycle through each of the levels
continuously.
3. Enter the cooking time using the number buttons.
4. Press the START/+30 SEC button to start the cooking cycle.
• When the cooking cycle finishes, the oven beeps and switches off.
Programmed buttons
To cook food in preset cooking sequences.
1. Open the oven door and put the food in. Close the door.
• The screen displays: 0. The light will switch on.
2. Press the necessary button.
• For single button programming,
only press one button.
• For two button programming,
press the same button twice.
• If the button has not yet been programmed
the screen will display NO DATA.
3. The oven starts to cook the food.
• The screen displays the total cooking time.
4. • When the cooking cycle finishes, the oven beeps and switches off.
Button Time
1 10 sec.
2 20 sec.
3 30 sec.
4 45 sec.
5 1 min.
DEFROST button
Defrosts food, dividing the total defrost time into alternate defrost and
rest periods by stopping and starting:
1. Open the oven door and put the food in. Close the door.
2. Press the DEFROST button.
• The DEFROST indicator switches on and the screen displays :0.
3. Press the number buttons(s) to enter the necessary defrost time.
4. Press the START/+30 SEC button.
5. The oven starts the cycle.
• The screen displays a countdown that shows the remaining defrost time DEFROST
mode.
NOTE: The oven beeps during the defrost cycle to warn that the food needs to be
turned over or repositioned.
6. Open the door and reposition the food. Close the door.
7. Press the START/+30 SEC button to proceed with the defrost cycle.
NOTE: If you do not open the door to reposition the food, the defrost cycle carries on.
(HM-1035 P)
Factory settings
Button
6
7
8
9
0
Time
1 min. 30 sec.
2 min.
3 min.
4 min.
5 min.