EINHELL 34.130.60 Manual De Instrucciones Original página 26

Anleitung_GE_CM_36_Li_SPK7__ 25.06.13 10:46 Seite 26
GB
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important. The carbon brushes should not be
replaced by anyone but a qualified electrician.
8.3 Servicing
Worn out or damaged blades, blade mounts, and
n
bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
Do not clean the lawn mower with running water,
n
particularly with high-pressure water. Ensure that
all mounting components (i.e. screws, bolts, nuts
etc.) are always tightened so that the equipment
can be safely operated at all times.
Frequently check the grass catch assembly for
n
signs of wear.
Replace excessively worn or damaged parts
n
immediately.
Store your lawn mower in a dry room.
n
In order to ensure that you enjoy your scarifier for
n
many years to come, all screwed parts, as well as
the wheels and axles, should be cleaned and
lubricated.
Keeping your hand mower in good condition not
n
only ensures a long lifespan and high
performance, but also enables the equipment to
thoroughly cut your grass with minimal effort. For
best results, clean the lawn mower with a brush or
rag. Do not use any solvents or water to remove
dirt.
The cutting components - i.e. the knife cage and
n
lower knife blade - are subjected to more wear
and tear than any other component of the unit.
Therefore, routinely check the condition of the
blade and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again. An
excessively vibrating mower means that the blade
is not properly balanced or has become deformed
from striking an object. In this case, the blade
must be repaired or replaced.
There are no parts inside the equipment which
n
require additional maintenance.
8.4 Replacing the blade
For safety reasons, we recommend having the blade
replaced by an authorized professional. Important.
Wear work gloves! Only replace the blade with a
genuine Einhell replacement blade, as this will ensure
top performance and safety under all conditions.
Carry out the following steps to change the blade:
Undo the fastening screw (see Fig. 18).
n
Remove the blade and replace with a new one.
n
26
When fitting the blade, make sure it is installed in
n
the right direction. The blade's air vanes must jut
into the motor compartment (see Fig. 18). The
dome mounts must be aligned with the punch
holes in the blade.
Then retighten the fastening screw. The tightening
n
torque should be approx. 25 Nm.
At the end of the season, perform a general
inspection of the lawn mower and remove any grass
and dirt which may have accumulated. At the start of
each season, ensure that you check the condition of
the blade. If repairs are necessary, please contact our
customer service center. Use only genuine spare
parts.
8.5 Ordering replacement parts:
Please provide the following information on all orders
for spare parts:
Model/type of the equipment
n
Article number of the equipment
n
ID number of the equipment
n
Spare part number of the required spare part
n
For our latest prices and information please go to
www.isc-gmbh.info
Spare blade art. no.: 34.054.850
9. Storage
Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing
temperature. The ideal storage temperature is
between 5 and 30 °C. Store the electric tool in its
original packaging.
10. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The
equipment and its accessories are made of various
types of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.