EINHELL RASARRO 36/42 Manual De Instrucciones página 17

Do not use your hands or feet to remove clippings
in or on the mower housing, but instead use
suitable tools such as a brush or a hand broom.
In order to ensure that the majority of grass
clippings are picked up, the inside of the catch
basket must be cleaned after each use.
Reattach the catch basket only when the motor is
switched off and the blade has stopped.
Lift up the chute fl ap with one hand and, holding
the catch basket by its handle with the other
hand, hang in the basket from the top.
7. Cleaning and maintenance
Danger!
Pull the safety plug before carrying out any
cleaning work (Fig. 15).
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
Do not clean the lawn mower with running
water, particularly with high-pressure water.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
•
For best results, clean the lawn mower with a
brush or rag.
7.2 Maintenance
•
Worn out or damaged blade, blade mounts,
and bolts should be replaced as a set by an
authorized
•
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Frequently check the grass catch assembly
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
Anl_Rasarro_36_42_SPK7_USA.indb 17 Anl_Rasarro_36_42_SPK7_USA.indb 17
EN
•
In order to ensure that you enjoy the
equipment for many years to come, all
screwed parts, as well as the wheels and
axles, should be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high
performance, but also enables the equipment
to thoroughly cut your grass with minimal
effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again.
An excessively vibrating mower means that
the blade is not properly balanced or has
become deformed from striking an object.
In this case, the blade must be repaired or
replaced.
•
There are no other parts inside the equipment
which require maintenance.
7.3 Replacing the blade
For safety reasons, we recommend having the
blade replaced by an authorized professional.
Important! Wear work gloves! Only replace the
blade with a genuine Einhell replacement blade,
as this will ensure top performance and safety
under all conditions.
Carry out the following steps to change the blade:
1. Undo the fastening screw SW13 (see Fig. 16).
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is
installed in the right direction. The blade
air vanes must project into the motor
compartment (see Fig. 16). The dome mounts
must be aligned with the punch holes in the
blade.
4. Then retighten the fastening screw with the
universal wrench (see Fig. 16). The tightening
torque should be approx. 25 Nm.
At the end of the season, perform a general
inspection of the lawn mower and remove any
grass and dirt which may have accumulated.
At the start of each season, ensure that you
check the condition of the blade. If repairs are
necessary, please contact our customer service
center. Use only genuine spare parts.
Spare blade art. no.: 3405457
- 17 -
15.12.2022 08:52:24 15.12.2022 08:52:24