Hama Nano Instrucciones De Uso página 6

For Set Top Boxes (STB)
Button
PRIME VIDEO
1. Switch the device you wish to operate on.
2. Press and hold the Setup button for approx. 3 seconds until the LED lights up.
3. Press the Power button once. Then press the button that stands for the brand of your
terminal (e.g. BACK for Panasonic).
4. Point the remote control at the device you wish to control.
5. The remote control now sends a new command to your device every 2 seconds. The
LED ashes once for each command and then lights up permanently again.
6. As soon as your device switches off, press the OK button to save the code. The LED
goes out.
7. Then test the remote control and check whether the desired functions can be
controlled. It is possible that the rst code found is not the most suitable, and possibly
not all functions are available. In this case, repeat steps 2 – 6.
Note
• If you want to switch to another brand during the search, simply press the key
assigned to that brand (e.g. >II for Sony). The code search will then continue for
this brand.
• After all codes assigned to a brand have been searched, the LED ashes 6 times
and Setup mode is terminated. If no suitable code has been found for your device,
start the code search for all brands.
• If no button is pressed for 35 seconds in Setup mode, the LED ashes 6 times and
goes out. The remote control exits Setup mode without changing the previous
settings.
• Press the Setup button to exit Setup mode.
5.2 Direct code entry
A code list is included in the universal remote control's extent of delivery. The code list
contains ve-digit codes for setting the remote control to work with most AV equipment
manufacturers.
For easy orientation, the codes are sorted rst by type of device (TV, STB) and within the
type of device alphabetically by brand name.
Note
This remote control does not have a separate numeric keypad, so the numbers are
assigned to the following keys. (See Fig. 2)
4
Brand
(All STB brands)
1. Switch the device you wish to operate on.
2. Press and hold the Setup button for approx. 3 seconds until the LED lights up to start
Setup mode.
3. Enter one of the 5-digit codes from the enclosed code list. The LED ashes brie y as
each number is entered.
4. If a valid code is entered, the LED goes out after the 5th number is entered and the
code is automatically saved.
5. Then test the remote control and check whether the desired functions can be
controlled. It is possible that the rst code found is not the most suitable, and possibly
not all functions are available. In this case, repeat steps 2 – 5.
Note
• If an invalid code is entered, the LED ashes 6 times and then lights up
permanently again. In this case, repeat entering the code (Step 3).
• If no button is pressed for 35 seconds in Setup mode, the LED ashes 6 times and goes
out. The remote control exits Setup mode without changing the previous settings.
• Setup mode can be ended at any time by pressing the Setup button.
The following QR code allows you to create a list of available codes for the brand of your
device.
https://support.hama.com/code nder
6. Control of different devices
With this remote control you can control not only TV sets but also STB devices (Set Top
Boxes - e.g. SAT receivers). In the factory setting, the remote control is preset to control
TV sets.
To toggle between the various devices, proceed as follows:
1. Brie y press the Setup button. The LED ashes once.
2. The remote control is now in control mode for STB devices. Each time the button is
pressed, the LED ashes once.
Return to TV mode:
1. Brie y press the Setup button. The LED ashes 2x.
2. The remote control is now in control mode for TV devices. Each time the button is
pressed, the LED ashes once.
7. Learning function
This remote control is equipped with a learning function. This allows you to transfer
functions from your original remote control to this universal remote control.