Safety Regulations; Layout And Items Supplied - EINHELL TC-GW 190 D Manual De Instrucciones

Ocultar thumbs Ver también para TC-GW 190 D:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 124
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1-8)
1. Handle
2. Operating status indicator
3. Thermostat control lamp
4. Housing cover
5. Gas bottle support surface
6. Castors
7. Welding current switch
8. ON/OFF/Voltage selector switch
9. CeCon plug
10. Earth terminal
11. Hose package
12. Gas nozzle
13. Burner
14. Guide rollers
15. Chain hook
16. Gas supply connector
17. Welding screen
18. Shielding gas hose
19. Pressure reducer
20. Pressure gage (gas fl ow rate)
21. Screw connector
22. Safety valve
23. Shielding gas hose connector
24. Rotary knob
Anl_TC_GW_190_D_SPK9.indb 25
Anl_TC_GW_190_D_SPK9.indb 25
GB
25. Burner switch
26. 3 x contact pipe
27. Handle for housing cover
28. Safety chain
29. Welding wire speed controller
30. Adapter cable
31. Pressure gage (bottle pressure)
a. 16 x Screw for castors
b. 16 x Spring ring for castors
c. 16 x Washer for castors
d. 2 x Hose clip
k. 1 x Safety glass frame
l.
1 x Welding glass
m. 1 x Transparent safety glass
n. 2 x Safety glass retaining bushes
o. 3 x Nut for handle
p. 3 x Screws for handle
q. 2 x Safety glass retaining pin
r.
1 x Handle
s. 1 x Welding screen frame
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
Open the packaging and take out the equip-
ment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
Welding set
Original operating instructions
Safety instructions
- 25 -
20.07.2017 09:16:22
20.07.2017 09:16:22

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

15.749.95

Tabla de contenido