Toshiba SUPER MODULAR MULTI MMY-MAP0501T8 Manual De Instalación página 16

7
ADDRESS SETUP
REQUIREMENT
• When a group control is performed over the
multiple refrigerant lines, be sure to turn on the
power supplies of all the indoor units connected in
a group in the time of address setup.
• If turning on the power for each refrigerant line to
set up address, a header indoor unit is set for
each line. Therefore, an alarm code "L03"
(Duplicated indoor header units) is output in
operation after address setup. In this case,
change the group address from the wired remote
controller so that only one header unit is set up.
Address setup procedure 2

Using SW13 and 14 on the interface P.C. board of the header
unit in each system, set up the system address for each system.
(At shipment from factory: Set to Address 1)
Note) Be careful not to duplicate with other refrigerant line or other
system address.
System address switch on outdoor interface P.C. board
SW13
System
address
1 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
: Is not used for setup of system address. (Do not change setup.)
‚
Check that the relay connectors between [U1U2] and [U3U4] terminals are come out in all the header units to
which the central control is connected. (At shipment from factory: No connection of connector)
ƒ
Turn on power of indoor/outdoor.
(In order of indoor → → → → → outdoor)
„
After approx. 1 minute, check that 7-segment display is
U.1.L08 (U.1. flash) on the interface P.C. board of the
header unit.
…
Push SW15 and start setup the automatic address.
(Max. 10 minutes for 1 line (Usually, approx. 5 minutes))
† When the count Auto 1 → → → → → Auto 2 → → → → → Auto 3 is displayed in
7-segment display section, and it changes from
U. 1. - - - (U. 1. flash) to U. 1. - - - (U. 1. light) , the setup
finished.
‡ „ †
Procedure to are repeated in other refrigerant lines.
SW14
3 4 1 2 3
× × × ×
× ¡ × ×
¡
× × ×
¡ ¡
× ×
¡
× × ×
¡ ¡
× ×
¡ ¡
× ×
¡ ¡ ¡
×
× × × ×
¡
× × ×
¡
× × ×
¡ ¡
× ×
× × × ¡
¡ ¡
× ×
(Example)
Wire
systematic
diagram
System
address
4
×
15
×
16
×
17
×
18
×
19
×
20
×
21
×
22
¡
23
¡
24
¡
25
¡
26
¡
27
¡
28
2
13
Group control over
multiple refrigerant lines
Outdoor Outdoor
Header
Indoor Indoor
Indoor
Remote
controller
Header unit interface P.C. board
ON ON ON
1 2 3 4 1 2 3 4 1 2 3 4
SW11 SW12 SW13
ON ON ON ON
1 2 3 4 1 2 3 4 1 1
SW06 SW07 SW08 SW09
¡
×
( : Switch ON,
SW13
1 2 3 4 1
× ×
× ¡
¡
×
¡ ¡
¡
×
¡ ¡
¡
×
¡ ¡
¡
×
¡ ¡
¡
×
¡ ¡
¡ ×
¡ ¡
U1 U2 U3 U4
For internal For wiring of
wiring between central control
indoor and system
outdoor
Indoor
ON
1 2 3 4
SW14
ON
2 3 4 1 2 3 4
SW10
: Switch OFF)
SW14
2 3 4
¡ ¡ ¡
¡ ¡ ¡
× × ×
× × ×
¡
× ×
¡
× ×
¡
× ×
¡
× ×
¡ ¡
×
¡ ¡
×
¡
× ×
¡
× ×
¡ × ¡
¡ ¡
×
U5 U6
For internal
wiring between
outdoor units