Maglite ML150LR7 Manual Del Propietário página 12

Operation - Getting the most out of Your ML150LR
Section 5
METHOD 1
1. Unscrew the tail cap, backing it out of the
barrel far enough that the flashlight will not turn
on. (Note: This may require the tailcap to be
removed from the barrel entirely).
2. Pause for 2 seconds.
3. Press the switch button and keep holding it down.
4. While still holding down the switch button, screw the
tail cap back in until it is tight.
5. Keep holding down the switch button. Within about
4 seconds the flashlight will start to blink.
6. The number of blinks indicates the new selected Function Set.
7. To choose a new Function Set, release the switch button after the corresponding
number of blinks (releasing after 1 blink chooses Function Set #1; releasing after 2 blinks
chooses Function Set #2; release after 3 blinks for Function Set #3, and release after 4 blinks to
choose Function Set #4.) Your choice of a Function Set remains in effect until you change it
by repeating the above process. (See our Demo video at www.maglite.com)
METHOD 2 - STEP 1
• Click the light into HIGH mode and hold the button down for five seconds.
NOTE: If the light is currently configured for Function Set 1 or 2, then the user will
begin from the OFF mode, click once and hold.
If the light is currently configured for Function Set 3 or 4, then the user will begin
from OFF mode, click twice and hold.
• After five seconds, the light will turn off for .25 seconds and then back on again
indicating that the light is now unlocked. The Function Set can be changed at turn-off
and without loosening the tail cap (traditional method).
• Release the button at any time.
STEP 2
• Click and hold the button down for five seconds.
• After five seconds the light will turn OFF, continue holding the button.
• After three seconds the light will begin to blink in successive patterns which
represent a particular Function Set, from this point everything is the same as the
traditional method.
NOTE: One blink, is Function Set 1 (GENERAL), release the button to save this set
into memory.
/ML150LRS LED Rechargeable Flashlight System
™ ™
Two blinks, Function Set 2 (OUTDOOR), release the button to save this set into
memory.
Three blinks, Function Set 3 (LAW ENFORCEMENT), release the button to save this
set into memory.
Four blinks, Function Set 4 (TACTICAL), release the button to save this set into
memory.
n NOTICE: To avoid deeply discharging the rechargeable LiFePO 4 battery, always turn
the flashlight off when the flashlight beam starts to dim. A dim beam is an indication that
the battery needs to be recharged.
Spot-to-Flood Beam
The quick focusing spot-to-flood beam operates with a simple quarter turn of the
flashlight head assembly.
Frequently Asked Questions
Q. How long can I leave the flashlight in the Charging Cradle (on charge) without
using?
A. Indefinitely. Your charging cradle is suitable for permanent stowage of the flashlight.
Because the cradle automatically shuts off when it detects that the flashlight has taken a full
charge, you don't ever have to worry about overcharging the flashlight. If the flashlight sits
idle in the cradle for a long enough time to lose a little of its charge, the cradle detects that,
too, and applies a "top off/maintenance" charge. But again, it will stop charging when the
charge is back up to 100%. The cradle will never overcharge the flashlight.
Q. If dust occurs inside my reflector, how do I clean it without damage to the
reflector?
A. Do not touch reflector. Use a camel hair brush lightly or blow with a compressed air duster
as used on computers and electronics. Use the same care that you would give a precision
camera lens.
Q. How do I get a fingerprint off my reflector?
A. Use a camera lens cleaner and a lint-free cloth.
11