EINHELL proviel HKG 210 Manual De Instrucciones página 14

Anleitung Hela HKG 210
GB
7. Assembly
A.) Adjusting the saw (Fig. 2)
While pressing down lightly on the machine head
(4), pull the lock pin (16) out of the motor holder
to disengage the saw from its bottom working
position.
Swing up the machine head until the retaining
hook latches home.
The machine head can be tilted a max. 45° to the
left by using the hex wrench (12) to undo the
clamping screw (13).
Check that the voltage marked on the rating plate
is the same as your mains voltage and connect
up the machine.
B.) 90° cross-cuts and 0° rotary table (Fig. 3)
Press the main switch (3) to turn on the saw.
Caution! Position the material firmly on the
machine bed so that it cannot move about while it
is being cut.
After switching on the saw, wait for the blade (5)
to reach its maximum speed.
Press the release button (1) and lower the
machine head by its handle (2) smoothly and with
slight pressure down through the workpiece to
make the cut.
When the cut is completed, return the machine to
its top parking position and let go of the On/Off
switch.
Caution! A return spring causes the machine
head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut
is completed but steady the machine head and
allow it to rise slowly.
C.) 90° cross-cuts and 0°-45° rotary table (Fig. 4)
The HKG 210 can be used to make angled cuts of
0°-45° relative to the stop rail on the left and right
side.
Undo the rotary table (8) by slackening the two
lock screws (19) on the stop rail.
Turn the rotary table (8) by its handle (2) to the
angle you want, i.e. the mark (a) on the rotary
table has to comply with the required angle
dimension (B) on the base plate (9).
Re-tighten the two lock screws (10) to fix the
rotary table (8) in position.
Make the cut as described in Section B.).
14
29.01.2002 11:57 Uhr
D.) Mitre cuts 0°-45° and rotary table 0° (Fig. 5/6)
The HKG 210 can be used to make mitre cuts of
0°-45° relative to the machine bed on the left side.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the clamping screw (13) with the hex
wrench (12) to and tilt the machine head (4) by its
handle (2) to the left until the mark (a) on the
machine head (4) points to the required angle
dimension (b).
Re-tighten the clamping screw (13) and make the
cut as described in Section B.).
E.) Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 7)
The HKG 210 can be used to make mitre cuts on the
left at an angle of 0°-45° relative to the work top and
0°-45° relative to the stop rail.
Lift the machine head (4) to its top position.
Undo the rotary table (8) by slackening the two
lock screws (10) on the stop rail.
Adjust the rotary table (8) by its handle (2) to the
required angle (see also Section C).
Re-tighten the two lock screws (10) to fix the
rotary table in position.
Undo the clamping screw (13) and tilt the
machine head (4) by its handle (2) to the required
angle dimension (see also Section D).
Re-tighten the clamping screw (13).
Make the cut as described in Section B.
F.) Chip extractor (Fig. 2)
The saw is equipped with a chip extraction socket
(18).
It is easy therefore to connect the machine to a chip
extraction system.
G.) Replacing the saw blade (Fig. 8)
Pull out the power plug.
Swing up the machine head (4).
Unscrew the 4 recessed head screws (17) and
take off the left saw blade cover (15).
Use the supplied face wrench (11) to lock the
outer flange in place and use the socket wrench
(12) to unscrew the hex screw (Important: left-
hand thread. Unscrew clockwise!).
Seite 14