Publicidad
Idiomas disponibles
Idiomas disponibles
G2408-115
Personal protective equipment must be used as
►
described in Section Personal protective equip-
ment
Slip/Trip/Fall is a major cause of serious injury
►
or death. Watch out for excess hose left on the
walking or work surface
Proceed with care in unfamiliar surroundings.
►
Hidden hazards may exist, such as electric or
other utility lines
Maintain a balanced body position and firm foot-
►
ing
Do not side grind with cutting off wheels and
►
straight wheels or with inside of cup wheels
React quickly to excessive vibration due to dam-
►
aged, or improperly mounted insert tool
Keep away from rotating drive spindle and abras-
►
ives. Rotation may continue for several seconds
after the throttle has been released. Do not lay the
tool down until rotation has stopped
Observe that stored compressed air in the hose
►
may cause an accidental start
Release control device if the energy supply should
►
fail
If a grinder fitted with an abrasive wheel is
►
dropped, the wheel must be thoroughly examined
before reuse
Disconnect from power supply before changing
►
wheel or servicing
Always keep the tool in a dry and clean place
►
when not in use
Broken grinding wheel
If grinding wheel is broken, a careful investigation
shall be made by the user to determine and correct
the cause.
If the failure occurs while the tools is in operation,
the wheel manufacturer and the tool manufacturer
should be notified promptly.
Maintenance
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles
cause rust and sticking of vanes, valves etc.
This can be solved by lubricating with oil (a few
drops), running the machine for 5-10 seconds and
wiping off excess oil with a cloth. Do this before
longer standstills.
EN
© Atlas Copco Industrial Technique AB - 9836 3803 00
Safety and operating instructions
Lubrication
The machine is fitted with an angle gear which is
lubricated with a semi-fluid grease to ensure good
wear resistance. To avoid overfilling, which could
result in a rise in temperature and damage to seals,
there is no lubrication nipple. Instead, the grease
should be changed after about 200 running hours by
removing the angle-gear spindle.
For accurate lubrication properties – use Urethyn
GE00 semi-fluid type grease. The requisite amount
3
of grease is max. 4cm
A
Do not use ball bearing grease or chassis
grease.
Lubricating guide
Use lubricants of good quality. The oils and greases
listed in the lubrication table are examples of lubric-
ants that can be recommended.
Brand
General purpose
Bearings
BP
Energrease LS-EP2
Castrol
Spheerol EP L2
Esso
Beacon EP2
Q8
Rembrandt EP2
Mobil
Mobilegrease XHP 222
Shell
Alvania EP2
Texaco
Multifak EP2
Molycote
BR2 Plus
Overhaul
T
WARNING Overspeed could result in serious
injury or death
If speed governor is used, check that correct speed
►
governor is assembled. Careless handling may put
it out of order
Do not disassemble security parts, e.g. speed
►
governor or overspeed shut-off. These parts must
be completely replaced when damaged
Always check the free speed of the machine after
►
service. See Section Preparation before using the
grinder
For preventive maintenance, the grease in the angle
gear should be changed after roughly 200 hours of
operation. See the directions under Lubrication.
The entire machine should be checked regularly
at six-months intervals. If it is in heavy duty service
or not running properly it should be taken out of
service more often for inspection.
Check the sealing lip and adjacent column for
wear. The seal is essential to keep lubricant in the
gear box.
.
Air lubrication
Energol E46
Arox EP46
Chopin 46
Almo oil 525
Tonna R32
Aries 32
7
Publicidad
