Publicidad
Idiomas disponibles
Idiomas disponibles
Installation instructions
FAUCET ASSEMBLY
FAUCET MOUNTING
INSTALLATION
Be sure there
is room
underneath
the sink to
make the needed
connections.
Select
one of
the following
locations
to install
the faucet:
• In an existing
sink spray
attachment
or soap
dispenser
hole.
• In a hole to be drilled
in the sink top.
• In a hole to be drilled
in the countertop,
next to the sink.
NOTE:
Be sure the faucet
base will
fit flat
against
the surface
at the selected
location
so the gasket
will
seal.
1.
If drilling
is needed,
make
a 1-1/4" dia.
hole. Be sure to use the proper
procedure
for drilling
porcelain
or stainless
steel.
Special
drill bits may be needed.
Consult
a qualified
plumber
for proper
procedure.
2.
Remove
the faucet, thin o-ring
(D), faucet
base (E), bottom
base gasket
(F), lock
washer
(G), hex nut (H) and mounting
bracket
(I) from the packaging.
3.
Feed the 3/8" blue banded,
1/4" black tube
(attached
to the Reverse
Osmosis
System)
and the 3/8" black tube
(included
in
separate
packaging)
up through
the
mounting
hole in the sink or countertop.
This step may require
two
people
to
assemble.
See page
14 for Optional
One Person
Faucet
Tubing
Installation.
4.
Feed the two
black tubes
up through
the
gasket
(F), faucet
base (E) and O-ring
(D).
Body (B)
Spout
Cap
_
Handle
/
O-ring (D)
p_z'/Base
(E)
_w-
/-Gasket
(F)
Mounting
bracket (I)
Lock washer (G)
Power
I_1--
Hex nut (H)
cord (L) -----_1_ _..
II_ _--Tubing
I_lln
adapter (K)
ASSEMBLED
NOTE:
For ease of service
and maintenance,
keep tubing
lengths
long
enough
so removal
of the Reverse
Osmosis
system
from
under
the sink is possible.
5.
Push the 1/4" black and 3/8" black tubing
onto their respective
fittings
on the body (B).
NOTE: To ease insertion,
submerge
tubing
ends
into hot water
for a few minutes
to soften.
6.
Seat the base (E) and body
(B) together.
Make sure the O-ring
and gasket
are
in place when
the base meets
the body.
The faucet
handle
will
be at the 3 o'clock
position
with
respect
to the base.
7.
Slide the lock washer
onto
the threaded
stem
of the body
(B), then
thread
the hex
nut (H) onto the stem. Screw about halfway
up.
NOTE: If installing
faucet
on a stainless
steel
sink, slide on installation
spacer (M) before
the
lock washer.
8.
Screw
the blue tipped
tubing
adapter
(K)
onto
the threaded
stem
of the body
(B).
9.
Push the blue banded
tubing
into the
adapter.
It should
go in about
3/4". Pull on
it to make sure
it is installed
correctly.
10. Feed the tubing,
stem
and power
cord
back down
through
the 1-1/4" hole.
11. Lower
the faucet
assembly
into
place
in the mounting
hole and orient
to final
position.
Place the mounting
bracket
(I)
above
the lock washer
(G) around
the
faucet
stem.
While
holding
the mounting
bracket
in place, securely
tighten
the
hex nut. This step may require
two people.
3/8" barb fittinc
3/8" (black)
drain tubin<
1/4" (black)
drain tubin(
barb fitting
spacer (M)
(as needed)
Lock washer (G)
Nut (H)
g adapter (K)
Power cord (L)
blue banded)
outlet tubing
13
To drain From RO From RO
Publicidad
