Kärcher VC 6 Manual De Instrucciones página 18

1. Press the unlocking button.
2. Remove the battery from the device.
Illustration J
Operation
LED display
The LEDs on the head of the device and on the battery
indicate information about the battery status, boost
mode and error messages.
The charging state of the battery is indicated by the
3 green LEDs on the device as well as by the 3 green
LEDs on the battery.
See figure A on the graphics page and chapter Descrip-
tion of the unit
Battery charging state
LED Duration of
lighting
1st LED flashes 1 s on / 1 s off Battery charged below
green
1st LED lights up continuously Battery charged below
green
1st and continuously Battery charged below
2nd LEDs light
up green
3 LEDs light up continuously Battery charged
green
3 LEDs flash 125 ms on /
green 125 ms off
The charging progress of the battery is indicated by the
3 green LEDs on the device as well as by the 3 green
LEDs on the battery. The LEDs only light up when the
battery is correctly installed.
While charging
LED Duration of
lighting
1st LED flashes 0.2 s from off
green to on /
0.6 s on /
0.2 s from on
to off /
1 s off
1st LED lights continuously
up green 0.2 s from off
2nd LED flashes to on /
green 0.6 s on /
0.2 s from on
to off /
1 s off
1st and continuously
2nd LEDs light 0.2 s from off
up green to on /
3rd LED flashes 0.6 s on /
green 0.2 s from on
to off /
1 s off
3 LEDs light up 2 min contin-
green uous lighting,
then off
18
Meaning
7.5 %
40 %
70 %
above 70 %
Battery fault, after 30 s
the signal goes out
Meaning
Battery charging, bat-
tery charged below
40 %
Battery charging, bat-
tery charged below
70 %
Battery charging, bat-
tery charged below
99 %
Battery fully charged
English
Error message
LED Duration of
lighting
Suction duct 125 ms on / 125
flashes red ms off
Floor nozzle 125 ms on / 125
LED flashes ms off
red
See also chapter Troubleshooting guide
Boost mode
LED Duration of
lighting
LED half ring continuously
lights up green
Changing accessories
To change accessories, see chapter Installing accesso-
ries
Vacuuming
1. Install the required accessories, see chapter Install-
ing accessories.
2. Switch on the device, depending on cleaning re-
quirements:
 Press the On/Off switch and keep it pressed dur-
ing operation.
or
 Turn the locking lever to switch the device directly
to continuous operation.
Illustration K
3. If necessary, press the Boost button to increase the
dust intake.
Illustration L
Note
When the device is switched off, the boost function is
automatically disabled.
The boost function can also be switched off by pressing
the Boost button again.
Ending operation
1. Switch off the device.
Release the On/Off switch or disable the locking le-
ver.
Note
To ensure an optimum suction performance, empty the
dust container and clean the air inlet filter after each
use.
Empty the dust container at the latest when the "MAX"
marking is reached.
2. Remove the suction pipe or accessory.
3. Empty the dust container into a waste container.
a Press the unlocking button.
The dust container flap opens.
b Empty the dust container.
Illustration M
4. To close the flap, push the dust container upwards
until it clicks into place.
5. Clean the air inlet filter, see chapter Cleaning the air
inlet filter
6. Depending on the scope of delivery, attach the unit
to the wall bracket or to the free-standing parking
station with charging function.
Illustration F
Illustration G
Meaning
Suction channel
clogged
Floor nozzle blocked
Meaning
Boost mode on