GE GXCC01D Manual Del Propietário página 7

Toremove
To replace
_ Support collar
Separator
Cleaning the Separator
IMPORTANT: Set both power switches (on the
back of the dispenser, ff equipped) in the 0 (off)
position and unplug the water dispenser before
cleaning.
1. Remove the water bottle and drain the
dispenser (see Draining the Dispenser).
2. Remove the support collar by turning
counterclockwise and pulling suaight off:
3. Remove the plastic separator by pulling
straight out (you may need to _vist slightly
to loosen).
4. Clean the separator with dish soap
and wateI or in rite top rack of rite
dishwasher:
5. D_T the separator flK_roughly on
boP1 sides.
6. Using a clean clod1 or paper towel,
flK_roughly d W the cold water reservoir
7. Place the separator back in the dispenser
Make sure the long, tapered end of the
separator is positioned firefly on the metal
plug on the bottom of the reservoir
8. Replace the support collar and mrn
dockwise until it is firefly in place.
9. Install a Pill water bottle on the dispenser
(see Loading the Dispenser).
Sanitizing and Cleaning the Water Tanks
IMPORTANT:Periodicafly the water dispenser tanks must be sanitized to prevent unpleasant tastes in the water and cleaned to
remove mineral deposits that can impair flow.
ToSanitize:
1.
Before cleaning, set both power switches
(on the back of the dispenser, if equipped)
u
in the 0 (off) posidon and unplug the water
OFF
dispenser, p0siti0n
NOTE:For first dine installation, skip
steps 2-4.
2.
Empty the water bottle, then remove it flom the
dispenser
3. Drain the water ranks (see Draining the
Dispenser).
4. Reinstall the silicon stopper and drain cap (on floor
models)or the drain cover and retaining clip (on countertop
models) (see
Draining the Dispenser).
5.
DO NOTADB BLEACHFIRSTORDIRECTLYTOTHE
DISPENSER.Concentrated bleach may damageplastic.
Add 1/2 teaspoon (2.5 ml) of ordinary 6.0% maximum
household bleach to a 2 quart (2 liter) pitcher filled
with mp water
6.
Pour the solution in the opening at the top of
the dispenser
7. Repeat steps 5 and 6 until the dispenser is fhll.
8. Press the hot and cold dispenser buttons until the
water just begins to flow flom the raps.
9. Allow to sit for 15-20 minutes.
10. Rinseout the bleach solution:
-- Drain the water ranks into a large bucket
(floor models) or sink (countertop models)
(see
Draining the Dispenser).
-- Make sure that the silicon stopper (floor
models) or drain cover (countertop models)
is N0Yinsmlled.
-- iMPORTANT: R emove the separator and wipe out
the cold water reservoir
(see
Cleaning the Separator).
-- Clean, then reinstall the separator and collar
(see
Cleaning the Separator).
-- Pour approximately 1 gallon (4 quarts or
4 liters) of flesh mp water into the top and allow
to drain into the bucket (floor models) or sink
(countertop models).
-- Flush with an additional 1 gallon (4 quarts or
4 liters) of flesh mp water and allow to drain
into the bucket (floor models) or sink (countertop
models).
11. Reinstallthe silicon stopper and drain cap (on floor
models) or the drain cover and retaining clip (on countertop
models) (see
Draining the Dispenser).
12. Install a flesh water bottle (see Loading the Dispenser).
13. Dispense f quart (I liter) of water from each tap
and taste to make sure the bleach soludon is
completely removed.
If you continue to taste the chlorine fromthe bleach solution,
repeat steps l&-13 until the taste is gone.
14. Plug in the dispenser. Then turn on the hot
and cold power switches (on the back of the
OR
dispenser, if equipped), position
ToRemoveMineral Deposits:
Mix 2 quarts (2 liters) of water with two quarts of vinegar ORmix I gallon of water (4 liters) with 16ounces (454 g) of citric acid
crystals. Bleach does not remove mineral deposits. Do this in pie ce of step 5 when removing mineral deposits.
7