EINHELL TE-SM 36/10 L Li Manual De Instrucciones Original página 26

All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
4. Technical data
Motor power supply ................................36 V d.c.
Idle speed n : ....................................... 3800 rpm
0
Carbide saw blade: ...........ø 254 x ø 30 x 2.5 mm
Number of teeth: ............................................ 40
Swiveling range: .......................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Saw width at 90°: ............................ 340 x 85 mm
Saw width at 45°: ............................ 240 x 85 mm
Saw width at 2 x 45°
(double miter cut, left): .................... 240 x 47 mm
Max. cutting height: .................................. 85 mm
Max. workpiece depth: ........................... 340 mm
Weight: ....................................... approx. 14.2 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class .......................................... III/
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 180 mm.
Anl_TE_SM_36_10_L_Li_Solo_SPK13.indb 26
GB
This machine is intended for use with rechargea-
ble batteries and chargers from the Einhell Power-
X family only. For the current models, please refer
to the product descriptions for the articles. These
are available online.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
L sound pressure level ..................... 86.1 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ........................ 99.1 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
- 26 -
10.07.2023 11:28:33