EINHELL TE-SM 36/10 L Li Manual De Instrucciones Original página 29

Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Battery capacity indicator (Fig. 16)
Press the button for the battery capacity indicator
(c). The battery capacity indicator (d) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED flashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove
the battery from the equipment, keep it at room
temperature for one day. If the fault reoccurs, this
means that the rechargeable battery has under-
gone exhaustive discharge and is defective. Re-
move the battery from the equipment. Never use
or charge a defective battery.
6.3 Adjusting the movable stop rail
(Figs. 17-20)
Warning! To make 90° crosscuts, the adjustable
stop rail (37) must be fi xed at the inner position:
•
Undo the locking screw (38) of the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (37) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (37) and
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (38) again.
Warning! To make 0°-45° miter cuts (with the
saw head inclined or the turntable set at an ang-
le), the adjustable stop rail (37) must be fi xed at
an outer position.
•
Undo the locking screw (38) of the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (37) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (37) and
Anl_TE_SM_36_10_L_Li_Solo_SPK13.indb 29
GB
the saw blade (7) amounts to a maximum of
5mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (38) again.
Warning! The adjustable stop rail on the right-
hand side must always remain fi xed at the inner
position.
6.4 Cross cut 90° and turntable 0°
(Fig. 1-4, 9, 17)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (10) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (10)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper po-
sition.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (11) and on the turntable (17).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Clamp flat material which has the wide side
lying on the table using the clamping device
aligned vertically (see Fig. 9a).
•
Alternatively, clamp flat material which has
the flat side on the table using the clamping
device aligned horizontally (see Fig. 9b).
•
Press the release lever (3) to release the On/
Off switch (2).
•
Press the On/Off switch (2) to start the motor.
•
With the drag guide fixed in place: Use the
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide not fixed in place: Pull the
machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the
very back until the saw blade (7) has comple-
tely cut through the workpiece.
•
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
- 29 -
10.07.2023 11:28:34