EINHELL TC-WG 200 Manual De Instrucciones Original página 17

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 13)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
5. Warning! Do not use a damaged grinding/
sanding wheel. Damaged plug-in tools may
break into pieces that are catapulted into the
surroundings.
6. Caution! Wear gloves.
7. Direction of rotation of the grinding/san-
ding wheel.
8. Caution! Do not use with hand-held ma-
chines. These grinding/sanding tools are
allowed to be used only on machines that are
not held in your hand.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
Anl_TC-WG_200_SPK13.indb 17 Anl_TC-WG_200_SPK13.indb 17
GB
2. Layout and items supplied
2.1 Layout (Fig. 1/2a-c)
1. On/Off switch
2. Clamping device
3. Clamping plate
4. Locking knob for clamping plate
5. Wet grinding wheel
6. Honing wheel
7. Transport handle
8. Mounting holes
9. Base plate
10. Water container
11. Overfl ow
12. Lower mounting eyelet
13. Upper mounting eyelet
14. Hook on water container
15. Grinding stone
16. Flange
17. Angle gauge
18. Knurled screw for wheel diameter
19. Scale for wheel diameter
20. Knurled screw for blade angle
21. Scale for blade angle
22. Notch for determining the angle
23. Edge
24. Support arm
25. Knurled nut for precision adjustment of the
support arm
26. Mounting hole for support arm (vertical)
27. Locking screw for support arm
28. Mounting hole for support arm (horizontal)
29. Drive shaft
30. Adjustment screw for pretensioning the drive
shaft
31. Locking knob for the honing wheel
32. Nut
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
- 17 -
13.06.2023 08:49:52 13.06.2023 08:49:52