Publicidad
Idiomas disponibles
Idiomas disponibles
BReAN
MODELS
EW5630SS
• EW5636SS
To replace a fuse (by qualified person(s):
1. Disconnect power at service entrance.
2. Remove decorative flues.
3. Remove control cover.
4. Remove and inspect fuse.
Page 8
MAKE-UP AiR DAMPER
The hood is compatible with Broan Make-Up Air Damper Model
MD6T or Model MDST (optional). Purchase separately.
GR
MAKE-UP AIR DAMPER
/I
MAKE UP DAMPER
CONNECTION
(switched
low voltage)
20 GAUGE
BELL WIRE
FOR LOW
"-
OLTAGE
CONNECTION
ON
TOP OF HOOD
""'--
24V
]
TRANSFORMER
/
_
DRY CONTACT
(INCLUDED)
/
TERMINAL
HOOD
BUSHING
FOR LOW
__
120 VAC
/"
VOLTAGE
--
60 HZ
I
CONNECTION
Make the connection to the Make-Up Air Damper with low voltage
wiring, as shown. See Make-Up Air Damper instructions for additional
information.
REMOTE CONTROL
The hood is compatible with Broan Radio Frequency (RF) Remote
Control Model BCR1 (optional). Purchase separately.
To link the BCR1 remote control with the hood, press and hold the
LIGHT button for 3-seconds.
The blue LED indicatorswill turn on and off in succession to indicate
the hood is in RF linking mode. When in the linking mode, press any
key on the RF remote. An audible beep will be heard at the hood, and
the hood LED's will stop blinking if a successful link is accomplished.
If the remote control did not successfully link with the hood, the linking
mode will be deactivated after 12 seconds, and the LED's will stop
the sequential blinking. Refer to the BCR1 instructions for additional
information.
CLEANING
& MAINTENANCE
For performance, appearance, and health reasons, clean filter, fan
and grease-laden surfaces. Use only a clean cloth and mild detergent
solution on stainless and painted surfaces.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filter may occur if using phosphate
detergents, or as a result of local water conditions - but this will not
affect filter performance. This discoloration is not covered by the
warranty.
Clean the non-duct recirculating filter surfaces frequently with a
damp cloth and a mild detergent. DO NOT immerse filters in water
or put in dishwasher. Change the non-duct recirculafing filters every
6 months. For replacement non-duct recirculating filters - purchase
$99010365 or Model FILTERE56.
The motor is permanently lubricated and never needs oiling. If the
motor bearings make excessive or unusual noise, replace the blower
assembly with an exact service replacement.
LIGHT BULBS
SUCTION
CUP TOOL
HALOGEN
" ROTATE
CLOCKWISE ._
WARNING
Bulbs may be hot. Always allow bulbs to cool down before removing
them.
Use (2) Halogen Bulbs (included with hood) - 120 V, 35 W, shielded
halogen bulbs - MR16 with GU10 base.
NOTE
Suction Cup Tool (included with hood) can be used to install and
remove light bulbs. Align pins on bulb with large diameter opening
on socket, then push bulb in towards hood and rotate clockwise
until firmly seated. The position of the bulb socket (depth) is
adjustable and may require adjustment when: a) certain brands of
bulbs are difficult to install, b) the bulb protrudes too far below the
light panel.
LAMP SOCKET
BRACKET
LIGHT
PANEL
SCREWS
To change the depth of bulb sockets:
- Remove 2 screws on light panel- set screws aside
- Remove Light Panel.
- Loosen 2 Screws holding Lamp Socket Bracket to Light Panel.
- Adjust socket!bracket to desired depth.
- Re-tighten screws securely.
- Re-attach light panel with 2 screws that were previously set aside.
Publicidad
