Publicidad
Idiomas disponibles
Idiomas disponibles
This product, excluding horizontal models (Table 1), is a device that must be installed vertically in
order to operate correctly. Once installation is complete, and before any water is added or the power
supply is connected, use a measuring instrument (i.e. a spirit level) to check that the device has been
installed perfectly vertical.
The appliance heats water to a temperature below boiling point. It must be linked up to a mains water
supply according to the appliance performance levels and capacity.
Before connecting the appliance, it is first necessary to:
- Check whether the characteristics (please refer to the data plate) meet the customer's requirements.
- Make sure the installation conforms to the IP degree (of protection against the penetration of liquids)
of the appliance according to the applicable norms in force.
- Read the instructions provided on the packaging label and on the appliance data plate.
This appliance was designed to be installed only inside buildings in compliance with the applicable
norms in force. Furthermore, installers are requested to keep to the following advice in the presence of:
- Humidity: do not install the appliance in closed (unventilated) and damp rooms.
- Frost: do not install the appliance in areas where the temperature may drop critically and there may
be a risk that ice may form.
- Sunlight: do not expose the appliance to direct sunrays, even in the presence of windows.
- Dust/vapours/gas: do not install the appliance in the presence of particularly dangerous substances
such as acidic vapours, dust or those saturated with gas.
- Electrical discharges: do not install the appliance directly on electrical supplies that aren't protected
against sudden voltage jumps.
In the case of walls made of bricks or perforated blocks, partition walls featuring limited static, or ma-
sonry different in some way from those stated, you first need to carry out a preliminary static check of
the supporting system. The wall-mounting fastening hooks must be designed to support a weight that is
three times higher than the weight of the water heater filled with water.
We recommend installing the appliance as close as possible to the delivery points to minimise heat loss
along the pipes. Local regulations may provide for restrictions on installation in bathrooms; observe any
regulatory minimum distances. To facilitate maintenance, make sure there is a clearance of at least 50
cm inside the enclosure for access to the electrical equipment.
HYDRAULIC CONNECTION
Connect the water heater's inlet and outlet with pipes or fittings that are able to withstand temperature
in excees of 90°C at a pressure exceeding that of the working pressure. Therefore, we advise against
the use of any materials which cannot resist such high temperatures.
The appliance must not be supplied with water of hardness less than 12°F, or with especially hard water
(greater than 25°F); we recommend installing a water softener, properly calibrated and controlled - do
not allow the residual hardness to fall below 15°F.
Screw a "T" piece union to the water inlet pipe with the blue collar. On one side of the "T" piece union,
screw a tap for draining the appliance that can only be opened with the use of a tool (Fig. 1, Rif.B).
On the other side of the "T" piece union screw the safety valve supplied (Fig. 1, Rif.A).
Safety group complies with the European standard EN 1487
Some countries may require the use of hydraulic special safety devices; the installer must check the
suitability of the safety device he tends to use.
Do not install any shut-off device (valve, cock, etc.) between the safety unit and the heater itself.
The appliance's drain outlet must be connected to a drain pipe of diameter at least equal to the of the
outlet itself, with a funnel to permit an air gap of at least 20 mm for visual inspection. Use a hose to con-
nect the safety group to the mains cold water supply; fit a cock if necessary (Fig.1, Rif.D).
In addition, a water discharge tube on the outlet (Fig.1, Rif.C) is necessary if the emptying tap is opened.
When installing the safety device, do not tighten it fully down, and do not tamper with its settings.
INSTALLING NORMS (for the installer)
15 / EN
Publicidad
