Publicidad
Idiomas disponibles
Idiomas disponibles
Transportation
The battery has been tested in accordance with the rel-
evant rules for international transport and can be
transported / shipped.
Storage
Note
Store the appliance in a dry room.
Consider the weight of the appliance when storing it.
1. Insert the appliance into the storage dock.
Illustration P
2. Put the crevice nozzle and the upholster brush into
accessory storage.
Care and maintenance
Note
Use the appliance only when all filters and the dust
container are installed.
Defective filters and filters that can no longer be
cleaned must be replaced.
Before doing any work on the appliance:
1. Switch off the appliance.
2. Unplug the power supply from the power outlet.
Cleaning the filter set and the dust container
ATTENTION
Incorrect cleaning of the HEPA filter set
Damage to the HEPA filter set
Do not clean the HEPA filter set in a washing machine.
Do not dry the HEPA filter set with a hair dryer.
The HEPA filter set ensures clean exhaust air.
Clean the HEPA filter set if it is visibly dirty.
Replace the HEPA filter set if it is visibly damaged.
We recommend replacing the HEPA filter set every
6 months based on your use of the device.
1. Unlock the dust container, and pull out the dust con-
tainer.
Illustration Q
2. Remove the HEPA filter set, and unplug the cyclone
body and cyclone filter from the dust container.
Illustration R
3. Carefully empty / knock the dirt out of the HEPA filter
set.
Illustration S
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
Fault
The appliance does not
run.
Suction capacity de-
creases. / Abnormal
sound or operating noise
which becomes louder.
Floor nozzle LED lights is
flashing / go out
Troubleshooting guide
Possible cause
Filter set / dust container is missing.
Battery is nearly empty.
The appliance is in danger of overheat-
ing.
Dust container is full.
HEPA filter set is clogged.
It is in danger of overheating.
4. Empty the dust container, and rub down the inside
using a cloth.
Illustration T
5. Turn the cyclone body counterclockwise, and sepa-
rate the cyclone body from the cyclone filter.
Illustration U
6. Clean the HEPA filter set, cyclone body, cyclone fil-
ter and dust container under running water.
Illustration V
7. Allow the HEPA filter set, cyclone body, cyclone filter
and dust container to dry completely.
Illustration W
8. Insert the cyclone body into the cyclone filter, and
turn the cyclone body clockwise to latch into place.
9. Insert the cyclone set into the dust container.
10. Install the HEPA filter set on the upper section of the
cyclone set, and align.
11. Align the mounting point on the appliance with the
desired mounting hole on the dust container, and
latch the dust container into place.
Illustration X
Cleaning / replacing the brush roller
Note
Replace the brush roller when it is damaged.
Only dry brush roller is allowed for replacement.
Do not dry the brush roller using a hairdryer.
1. Pull the release button, and pull out the roller lever
and brush roller.
Illustration Y
2. Remove the roller lever from the brush roller.
Illustration Z
Brush roller
1
Roller lever
2
3. Clean up the winding hair in brush roller and brush
lever.
4. Install the brush lever into the brush roller.
5. Insert dry or new brush roller into floor nozzle, and
fix the brush roller into place.
Illustration AA
Ensure that the brush roller fits properly.
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Remedy
1. Install the filter set and the dust container
before using the appliance.
1. Charge the battery.
1. Check whether the dust container is
clogged.
2. Clean the dust container.
3. Switch the appliance on again.
1. Check the dust container.
2. Empty / clean the dust container, the HEPA
filter and the cotton filter.
3. Check and clean the cyclone set.
1. Check whether the brush roller is blocked,
and clean the brush roller.
2. Switch on the appliance again.
Publicidad
