Publicidad
Idiomas disponibles
Idiomas disponibles
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Installing / Removing the side handle
Change rotation speed*
1
How to use the LED light
Mounting the drill bit
Removing and mounting the chuck
wrench
Reversing the rotational direction*
Switch operation
Remaining battery indicator
Fixing the body in place (When
rotating forward)
Fixing the body in place (When
rotating in reverse)
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
Selecting accessories
*1 Change rotation speed
CAUTION
○ Before operating the change lever, check and make
sure that the motor has stopped.
A failure can occur if it is operated while the motor is
running.
Figure
Page
3
2
4
2
5
2
6
3
7
3
8
3
9
3
2
10
3
11
3
12
4
14-a
4
14-b
4
15-a
4
15-b
4
16
4
—
211
11
○ To operate the change lever, press the push button,
and release the lock of the change lever. Also, check
and make sure after operation that the push button has
returned and that the change lever has been locked.
○ Switch the change lever without mistake. If it is used at
a position halfway, there is a fear that the service life of
the switching mechanism may be shortened.
*2 Reversing the rotational direction
CAUTION
When the selector switch is in the center position, the
trigger switch cannot be pulled (Fig. 10-a). Always set
the selector switch to the center position or remove the
battery pack before performing maintenance, changing
accessories, storing the tool and any time the tool is not
in use.
RFC (Reactive force control)
This product features RFC.
This stops the motor automatically if the tool is jerking
excessively.
The LED light flashes to indicate that RFC has been
activated.
If this occurs, release your finger from the switch before
restarting. (Fig. 13)
NOTE
○ RFC may not always activate under certain working
conditions or situations.
When working, ensure that the material is securely
placed and fastened, hold the tool body securely, and
be sufficiently careful not to suddenly apply a large load
to the tool tip.
○ Take care to hold the tool firmly to prevent any jerking
motion.
○ RFC may also activate if you change position suddenly
while holding the tool.
LED LIGHT WARNING SIGNALS
This product features functions that are designed to protect
the tool itself as well as the battery. If any of the safeguard
functions are triggered during operation, the LED light will
blink as described in Table 3.
When any of the safeguard functions are triggered,
immediately remove your finger from the switch and follow
the instructions described under corrective action.
Table 3
LED Light Display
Overburden Protection
If the operating with the change
lever set on "2", adjust to "1" and
On 0.1 second/off
continue operation. Remove the
0.5 second
cause of the overburdening.
Blinks for approx.
RFC
3 sec after the
Remove the problem causing
switch has been
the tool to jerk excessively.
released.
When operating the tool, firmly
hold the tool to make sure it
doesn't jerk.
On 0.5 second/
Off 0.5 second
Temperature protection
Allow the tool and battery to
Blinks while
thoroughly cool.
protection is in
effect.
English
Safeguard Function
Publicidad
