HIKOKI RA 18DA Instrucciones De Manejo página 12

English
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action
When blowing off or infl ating
When defl ating
Inserting and removing the battery
(sold separately)
Charging
Mounting and removing the hook
Attachment of air dusting nozzle, and
examples of use*
1
Attachment of Nozzles (A) and (B),
and examples of use (infl ating)*
Infl ation technique*
3
Attachment of Nozzles (A) and (B),
and examples of use (defl ating)*
Air dusting nozzle storage*
Switch operation
Continuous operation*
6
Remaining battery indicator
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
Figure Page
1-a
1-b
3
4
5
6
7
2
8
9
4
10
5
11
12
13
15-a
15-b
16
17
―
*1
WARNING
○ Be careful when blowing air into tight spaces or upwind,
because objects blown into the air may be blown back at
you.
○ Do not turn on the switch when the air intake is close to
the ground or near objects that can easily be sucked in.
Dust and debris may clog the air intake and cause
malfunction.
Before turning on the switch, check the following.
○ There must be no people in the direction of the airfl ow.
○ There must be no loose objects in the area that would
cause a problem if they are blown into the air.
NOTE
This tool puts out warm air due to its structure, but this is
not a malfunction.
*2
NOTE
○ This tool puts out warm air due to its structure, but this is
not a malfunction.
○ To avoid over-infl ating, continuously check the condition
while infl ating.
There is a risk of rupture or damage.
○ Depending on the object to be infl ated, it may not be
adequately fi lled with air.
If the infl ation is too weak, additionally use a manual
pump to adjust the tension.
○ Do not forcefully tap the tip of the nozzle (B) against the
fl oor or other surfaces.
Doing so may cause deformation of the tip.
[Nozzle (A)]
For large items such as air mattresses, insert the nozzle
(A) into the air plug. (Fig. 7-a)
[Nozzle (A) + Nozzle (B)]
For smaller items such as beach balls or swim rings,
insert the tip of Nozzle (B) into the air plug fi rst, and then
2
insert Nozzle (A). (Fig. 7-b)
2
*3
○ Pull on both the air plug side and the material of the back
side to create a space inside.
2
○ Insert the tip of Nozzle (B) into the air plug, then insert
Nozzle (A).
3
*4
3
NOTE
The blow port is on the operator's side, so please use the
3 tool in such a way that it does not directly blow at your
face or body.
*5
3
NOTE
Hold the tool by the handle when carrying it. In particular,
4
do not lift or carry the tool by the stored air dusting
nozzle.
4
The nozzle may come off and cause it to drop or break.
*6
4 This product is equipped with a continuous operation feature
that is convenient for infl ating/defl ating and for cleaning wide
4
areas.
Pull the switch all the way twice quickly and release it to
4
activate "High-Power Blowing" continuous operation.
5
Pull the switch partially twice quickly and release it to activate
"Low-Power Blowing" continuous operation.
Pull the switch again to stop.
5
NOTE
When pulling the switch intermittently, the tool's
5
response may be delayed, but this is not a malfunction.
5
5
220
12