Publicidad
Idiomas disponibles
Idiomas disponibles
1/3
Z_ CAUTION:
Do not attempt to unclog the blade chamber by dropping
or tapping the mower on the ground. This can damage the mower.
DISCHARGING
The mower is designed
to disperse the clippings back to the lawn.
1. Discharging
may be necessary
if the grass fills the optional
bag too
quickly.
2. Clippings
may be further dispersed,
if needed, by blowing them with
a yard blower.
3. In heavy grass conditions,
a narrower
pass may be required
OPTIONAL
GRASS BAG (AVAILABLE AS AN OPTION
AT EXTRA
COST)
It is recommended
to bag the clippings for the first few spring
mowings
and the last mowing of the season to discourage
diseases.
1. Bagging the clipping is sometimes
preferred to reduce tracking of
clippings
into pools, hot tubs, and homes.
2. Clippings can be added to your compost bin and used later for a
natural fertilizer.
CLEANING AND STORAGE
z_ DANGER: Be sure the mower is unplugged and the blade has
stopped.
Remove and clean any debris from the outside of the mower and
inside of guard before storage. Store under cover. See
MAINTENANCE
section.
Cleaning out the underside of the mower is done easiest immediately
after mowing (ENSURE MOWER
IS UNPLUGGED
AND BLADE HAS
STOPPED). A rag, crumpled newspaper
or paper towels, can be used
to wipe out caked clippings. Be careful of sharp edges of blade.
A clean mowing deck improves the efficiency of the blade and
maintains high performance.
When cleaning,
DO NOT immerse mower
in water or squirt it with a hose or pressure washer. Use only mild soap
and damp cloth to clean the mower. Never let any liquid get inside the
mower; never immerse any part of the mower into a liquid.
NOTE:
Do not store the mower on or adjacent to fertilizers or chemicals.
Such storage can cause rapid corrosion to metal parts.
PREVENTING
CORROSION
Fertilizers and other garden chemicals
contain agents that greatly
accelerate
the corrosion of metals. If you use the mower in areas
where fertilizers or chemicals
have been used, the mower should be
cleaned immediately
afterwards.
Wipe all exposed parts with a damp cloth. You may lubricate only metal
parts with a light petroleum based oil. Do not lubricate wheels.
MAINTENANCE
Before each mowing session unplug the mower and ensure that the
blade has stopped. Check all nuts, bolts and screws to ensure proper
tightness, Be sure to check the blade fastening system.
IMPORTANT:
To assure product SAFETY and RELIABILITY,
repairs,
maintenance
and adjustment
should be performed by authorized
service centers or other qualified service organizations.
Use only
identical replacement
parts.
Inspect and thoroughly clean your mower at the beginning of each
mowing season for longer life and better performance.
From time to time turn the mower off and wait for the blade to stop.
Then unplug the power cord and turn the mower on its side. Using an
object such as a stick or rag, wipe out any accumulation
of grass in the
blade area. Also clean out any grass or debris which may be packed
around the discharge/mulch
door area.
Be careful of the sharp edges
of the blade.
REMOVING AND INSTALLING BLADE (FIGU RE 10,11,12)
1. RELEASE SWITCH
LEVER TO TURN MOWER
OFF, WAIT FOR
THE BLADE TO STOP, AND UNPLUG
MOWER.
THEN TURN
THE MOWER
OVER FOR ACCESS
TO THE BLADE.
2. Use a piece of 2x4 wood (about 2 feet long) to keep blade from
turning while removing flange nut.
3. Wear gloves and proper eye protection.
Be careful of sharp edges
of blade. Position wood and remove flange nut as shown in
Figure 10.
4. Remove square metal blade spacer, square plastic blade insulator,
and blade (Figure 11). Examine blade insulator for damage and
replace if necessary.
5. When replacing
sharpened
or new blade on shoulder
of fan, make
sure the "GRASS SIDE" on the blade will be facing the ground
when the mower is returned to its normal upright position.
After
installing
blade, place blade insulator
on blade such that the raised
lips on one side engage the edges of the blade.
Then install the
blade spacer so that it sits inside the raised lips on the other side
of the blade insulator.
Be sure to align the flats in the hole of the
blade spacer with the flats of the shaft, rotating the blade and
blade insulator together as necessary.
Position piece of wood to
keep blade from turning (Figure 12).
Install flange nut with the
flange against the blade spacer and securely tighten.
O
Fig. 11 A. nut, B. spacer, C. insulator,D. blade
SHARPENING AND BALANCING THE BLADE:(FIGURE 13,14)
1. BE SURE THE SWITCH
LEVER IS RELEASED AND THE BLADE
HAS STOPPED AND THE CORD UNPLUGGED
BEFORE
REMOVING
THE BLADE.
2. At all times be careful of sharp edges of blade.
3. Remove blade from mower. See instructions
for removing and
installing
blade.
4. Secure blade in a vise as shown in Figure 13.
5. Wear proper eye protection
and be careful not to cut yourself.
6. Carefully
file the cutting edges of the blade with a fine tooth file or
sharpening
stone, maintaining
the original cutting angle.
7. Check balance of blade by placing center hole in blade over a nail
or round shank screwdriver,
clamped
horizontally
in a vise. If either
end of the blade rotates down, file off additional
material from that
end. Blade
is properly
balanced when neither end drops.
(Figure 14)
8. Replace blade on mower and tighten securely.
LUBRICATION:
No lubrication is necessary. Do not oil the wheels. They have plastic bearing
surfaces which require no lubrication.
ACCESSORIES:
Recommended
accessories
for use with your tool are available from
your local dealer or authorized service center. If you need assistance
regarding
accessories,
please call: 1-800-544-6986.
Z_WARNING:
The use of any accessory
not recommended
for use
with this tool could be hazardous.
Publicidad
