Makita UB402MP Manual De Instrucciones Original página 11

ASSEMBLY
WARNING:
Before assembling or adjusting the
equipment, switch off the motor and remove the battery
cartridge. Otherwise, the fans may move and result in an injury.
WARNING:
When assembling or adjusting
the equipment, always put it down. Assembling or
adjusting the equipment in an upright position may
result in serious injury.
WARNING:
Follow the warnings and precau-
tions in the chapter "SAFETY WARNINGS" and
the instruction manual of the power unit.
Mounting the attachment pipe
CAUTION:
Always check that the attachment
pipe is secured after installation. Improper instal-
lation may cause the attachment falling off from the
power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1. Remove the cap from the end of the pipe.
► Fig.4: 1. Pipe 2. Cap
NOTICE:
Do not dispose of the cap since the cap
is necessary for storing the attachment.
2. Turn the lever toward the attachment.
► Fig.5: 1. Lever
3.
Align the pin with the arrow mark on the power
unit. Insert the pipe until the release button pops up.
Make sure that the position line is on the tip of the arrow
mark on the power unit, and the arrow mark on the power
unit and the arrow mark on the pipe are facing each other.
► Fig.6: 1. Release button 2. Arrow mark on the power unit
3. Pin 4. Position line 5. Arrow mark on the pipe
4.
Turn the lever toward the power unit.
► Fig.7: 1. Lever
Make sure that the surface of the lever is parallel to the pipe.
NOTICE:
Do not tighten the lever without the
attachment pipe inserted. Otherwise the lever may
tighten the entrance of the drive shaft too much and
damage it.
To remove the pipe, turn the lever toward the attachment and
pull the pipe out while pressing down the release button.
► Fig.8: 1. Release button 2. Lever 3. Pipe
Installing the end nozzle
Align the protrusion on the blower pipe with the groove on
the end nozzle, then attach the end nozzle to the blower
pipe, and then turn the end nozzle to lock it into place.
► Fig.9: 1. Triangle mark 2. End nozzle 3. Blower pipe
To remove the end nozzle, perform the installation
procedure in reverse.
NOTE: The length of the nozzle can be changed by
moving the nozzle as shown in the figure.
► Fig.10
Installing the flat nozzle or
extension nozzle
Optional accessory
1. Remove the end nozzle from the attachment.
2. Attach the flat nozzle or extension nozzle to the
attachment, and then turn it to lock it into place.
► Fig.11: 1. Flat nozzle 2. Extension nozzle
3. Attachment
Installing the gutter nozzle set
Optional accessory
1. Remove the end nozzle, extension nozzle, or flat
nozzle from the attachment.
2.
Loosen the screw on the small hose clamp, and
pass the hose clamp through the attachment.
► Fig.12: 1. Screw 2. Hose clamp (small)
3. Attachment
3. Connect the extension pipe to the attachment.
Align the groove on the extension pipe with the protru-
sion on the attachment, and then slide the extension
pipe along its groove so that the triangle markings face
each other.
► Fig.13: 1. Extension pipe 2. Attachment
4. Place the hose clamp onto the groove as illus-
trated and tighten the screw.
► Fig.14: 1. Screw 2. Hose clamp
5.
According to the working height, connect the rest
of extension pipes to the extension pipe which has
already been attached.
CAUTION:
When using the gutter nozzle set
in conjunction with a multi function power head
and blower attachment, do not use three or more
extension pipes. It may cause imbalance and result
in injury.
6.
Turn the outlet of the end nozzle as shown in the
figure.
► Fig.15
7. Connect the end nozzle to the extension pipe.
When connecting, align the triangle marking on the end
nozzle and the extension pipe, and then push the end
nozzle until it clicks. After that, rotate the end nozzle to
a suitable position for your work.
► Fig.16: 1. End nozzle 2. Extension pipe 3. Triangle
marking
When removing the end nozzle, align the triangle mark-
ings on the end nozzle and extension pipe, and then
pull out the end nozzle from the extension pipe.
► Fig.17: 1. End nozzle 2. Extension pipe 3. Triangle
marking
11 ENGLISH