Publicidad
Idiomas disponibles
Idiomas disponibles
m
1
7----
3,4
QQC
OOC
j2
The unit can be turned on at a specified
time every day with the
built-in
tiimer.
Preparation
Make sure the clock is set correctly.
1 Press
one of the function
buttons
to select
a
source.
• If TIJNER/BAND is pressed, the band cannot be selected in
this step.
2 Press TIMER while pressing SHIFT on the remote
control so that _) appears on the display.
Time and audiosource name flash alternately.
®
3 Within 6 seconds, press <1<1or _
to designate
the timer-on
time, then press II.
Pressing
either button changes
both the hour and the minute.
Holding it down will vary the time rapidly by lO-minute
interval,
and pressing
it repeatedly
will vary by 1 minute interval.
4 Within 4 seconds,
press _
or I_l_ to select the
duration for the timer-activated
period.
The ,duration
can be set between
5 and 240 minutes
in 5
minute steps.
The duration
will be automatically
set after 4 seconds.
It will
also be set if II is pressed
within 4 seconds
after step 4.
5
7
Adjust the volume.
The source sound will play at the volume
level set in this step
when the power is turned on by the timer.
If the volume
level
is set to 17 or higher,
however,
it will
automatically
be set to 16 when the power is turned on.
Prepare the source.
To listen to a CD, load the disc to be played first on tray 1.
To listen to a tape, insert the tape into deck 1 or 2.
To listen to the radio, tune in to a station,
Press POWER
to turn off the power.
When the timer-on time is reached, the unit turns on and
begins play with the selected source.
Get ready for the tape function
or the timer
recording.
To listen to the tape, press I_.
To record the source,
press •
on deck 1.
When
the timer-on
time is reached,
the unit turns
on and
begins
play with the selected
source.
While
the timer
is in
operation,
the display indication
is dimmer
than usual.
You can change
the source
that was selected
in step
1 by
pressing
one of the function
buttons
before pressing
II in step
3.
The timer
recording
period
and tape
length
When the length of the tape to be recorded
is shorter
than the
timer recording
period,
•
on deck 1 is released
before the timer
is off.
When the tape length is longer than the timer recording
period,
•
is not released.
If •
is not released
for a long time, the tape
in the deck may be damaged.
Press II/_
to release
•.
To check the timer setting
Press TIMER while pressing SHIFT on the remote control.
The selected source, the timer-on time, and the duration for the
timer-activated period will be displayed for 4 seconds.
To change
any of the previous
setting
Carry out from step 1.
However,
if you do not change the timer-on
time, in step 3 just
press II twice and continue
from step 4.
To cancel the timer standby mode temporarily
Press TIMER repeatedly while pressing SHIFT on the remote
control to display "-OFF ''.
To restore the timer standby mode, press again to display _).
Using
the unit while
the timer
is set
You can use the unit normally
after setting
the timer.
Before turning
off the power, check whether
the contents
in step
5 and 6 are set as you wish, turn off the power and carry out step
8 if necessary.
• Timer playback
will not begin unless the power is turned off.
• Connected
equipment
cannot be turned on and off by the built
in timer of this unit. Use an external
timer.
n,
i&l
ENGLISH
15
d
0
Publicidad
