Publicidad
Idiomas disponibles
Idiomas disponibles
afros dentro
se anteojos
cuando
na m_tscara
• la posici6n de
a tlave al aban-
o no autorizado.
_erruptor de la
Ira que "STOP"
argue (muerta).
los, cuando
el
or andando en
motor caliente
_=ponga "car6."
_iempre pare el
eas con c_sped.
el tractor com-
anteriormente,
1 del operador.
LA ACELER-
.'eleraci6n
ocidad inferior
miento dis-
:he a la veloci-
cuando est6
No Io use pare
trangulaci6n, tire
._mente, empuje
lesengancharlo.
TO LEVEL
MOWER
Make sure tires are properly
inflated to
the PSI shown on tires.
If tires are over
or under inflated,
it may affect the appear-
ance of your lawn and lead you to think
the mower is not adjusted
properly.
VISUAL
SIDE-TO-SIDE
ADJUSTMENT
1. With all tires properly
inflated and if your
lawn appears
unevenly
cut, determine
which
side
of mower
is cutting
lower.
NOTE: As desired,
you can raise the low
side of mower
or lower the high side.
2.
Go to side of mower you wish to adjust.
3.
With a 3/4" or adjustable
wrench,
turn
lift link adjustment
nut (A) to the left
to lower the mower, or, to the right to
raise the mower.
)
Turn nut right
Turn nut left
to raise mower
to iower mower
NOTE:
Each full turn of adjustment
nut will
change
mower height about 3/16".
4.
Test your adjustment
by mowing
some
uncut grass and visually
checking
the
appearance.
Readjust,
if necessary,
until you are satisfied
with the results.
PRECIS ION SIDE-TO-SIDE
ADJUSTMENT
1. With all tires properly
inflated,
park
tractor on level ground or driveway.
_, CAUTION:
Blades
are sharp. Protect
your hands with gloves and/or wrap blade
with heavy cloth.
2.
Raise mower to its highest
position.
3.
At both sides of mower, position
blade
at side and measure
the distance
(A) from bottom
edge of blade to the
ground.
The distance
should
be the
same on both sides.
4.
Ifadjustmentis
necessary, see steps 2 and
3 in Visual Adjustment
instructions
above.
5.
Recheck
measurements,
adjust if nec-
essary until both sides are equal.
FRONT-TO-BACK
ADJUSTMENT
IMPORTANT:
Deck must be level side-
to-side.
To obtain the best cutting results, the mower
blades
should
be adjusted
so the front
tip is 1/8" to 1/2" lower
than
the rear tip
when
the mower
is in its highest
position.
CAUTION:
Blades are sharp. Protect
your hands with gloves and/or wrap blade
with heavy cloth.
o Raise mower to highest
position.
, Position
any blade so the tip is pointing
straight
forward.
Measure
distance
(B)
to the ground
at front and rear tip of the
blade.
,
If fronttip
of blade is not 1/8" to 1/2" lower
than the rear tip, go to the front of tractor.
• With an 11/16" or adjustable
wrench,
loosen jam nut A several turns to clear
adjustment
nut B.
o With a 3/4" or adjustable
wrench,
turn
front link adjustment
nut (B) clockwise
(ltighten)
to raise the front of mower, or,
counterclockwise
(loosen)
to lower the
front mower.
Tighten adjust nul
B to raise mower
Loosen adjust nut
B to lower mower
25
Loosen jan1 nut A first
Publicidad
