Publicidad
Idiomas disponibles
Idiomas disponibles
iMPORTANT:
Your tractor is equipped
with a 12 volt system.
The other vehicle
must also be a 12 volt system.
Do not use
your tractor
battery to start other vehicles.
TO ATTACH JUMPER
CABLES
-
1,
Connect
one end of the RED cable
to the POSITIVE
(+) terminal
of each
battery(A-B),
taking care not to short
against tractor chassis.
2.
Connect
one end of the BLACK
cable
to the NEGATIVE
(-) terminal
(C) of
fully charged
battery.
3. Connect
the other end of the BLACK
cable (D) to good chassis
ground,
away from fuel tank and battery.
TO REMOVE
CABLES,
REVERSE
ORDER
-
1. BLACK
cable first from chassis
and
then from the fully charged
battery.
2.
RED cable last from both batteries.
Weak or Dead
Fully Charged
Battery
Battery
REPLACING
BATTERY
_WARNiNG:
Do not short
battery
ter-
minals
by allowing
a wrench
or any other
object to contact both terminals
at the same
time.
Before
connecting
battery,
remove
metal bracelets, wristwatch
bands, rings, etc.
Positive
terminal
must be connected
first to
prevent sparking from accidental
grounding.
1. Lift hood to raised position.
2.
Disconnect
BLACK
battery
cable (A)
then RED battery
cable and carefully
remove battery
from tractor.
3.
install new battery with terminals
in
same position
as old battery.
4.
First connect
RED battery
cable
(B) to
positive
(+) battery terminal with hex bolt
and keps nut as shown.Tighten
securely.
Slide terminal
cover
(C) over terminal.
5.
ConnectBLACKgroundingcableto
nega-
tive (-) battery
terminal
with remaining
hex bolt and keps nut. Tighten
securely.
6.
Close hood.
(Red)
_
'
Cable
(_
Negative
y
(Black)
___
Cable
TO REPLACE
HEADLIGHT
BULB
1. Raise hood.
2. Remove
bulb holder from the hole in
the backside
of the grill.
3.
Replace
bulb in holder and install bulb
holder securely
back into the hole in
the backside
of the grill.
4.
Close hood.
INTERLOCKS
AND RELAYS
Loose or damaged
wiring
may cause
your tractor
to run poorly, stop running,
or
prevent
it from starting.
, Check wiring.
See electricalwiring
diagram
in the Repair Parts section.
TO REPLACE
FUSE
Replace with 30 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
TO REMOVE
HOOD AND GRILL
AS-
SEMBLY
1. Raise hood,
2.
Unsnap
headlight
wire connector.
3.
Stand in front of tractor.
Grasp hood at
sides, tilt toward engine
and lift off of
tractor.
4.
When replacing
hood, be sure to re-
connect
the headlight
wire connector.
Hood
Headlight Wire
Connector
REVIStON
D
LLANTAS
Las llantas en
masiado en la
presi6n de las
para obtener e
• Reduzca la
PSI que se
REVISION
13
CONjUNTO
Para obtener I,
la caja de la s_
en la forma ad
LA CAJA DE t
Servicio y Aju.,
REVISION
I:
DA DE TOD,
Vea las figura'.
correas de irnl
dora y de mov
y Ajustes.de e
correas
slgan
REVISION
IE
Una vez que
jar su tractor,
correctamentE
FUNCIONA B
servicio y ajus
28
Publicidad
