Publicidad
Idiomas disponibles
Idiomas disponibles
Operation
5
BeforeStarting
i_ll
WARNING!
Read, understand
and follow
all
instructions
and warnings
on the machine
and in
this manual
before operating.
NOTE: For complete
and detailed
engine
starting,
stopping
and
storing
instructions,
it is recommended
that you read the engine
manual also included
with this unit.
1.
The spark plug wire was disconnected
for safety. Attach
the spark plug wire to the spark plug before starting.
Starting the Engine
1.
To avoid carbon
monoxide
poisoning,
make sure the
engine is outdoors
in a well-ventilated
area.
2.
Insert the ignition
key into the slot. Turn key to ON position.
3.
Now follow
the instructions
below
as it pertains
to your
machine.
ElectricStarter
1.
WARNING!
The electric
starter must be used with
a properly
grounded
two-prong
receptacle
at all
times to avoid the possibility
of electric
shock.
Follow all instructions
carefully
prior to operating
the electric
starter.
The electric
starter is equipped
with a grounded
two-wire
power cord and a plug. It is designed
to operate on a 110
volt AC household
current.
2.
Move the Choke Control
to the "Full" position.
3.
Push the Primer three (3) times, making
sure to cover the
vent hole when pushing.
4.
Connect
the power cord to the switch
box on the dash
panel. Plug the other end of the power cord into a three-
prong
110-volt, grounded,
AC receptacle.
5.
Push the starter button
to crank the engine.
6.
When engine
starts, release starter button,
and move
choke gradually
to 1/2 Choke until engine
runs smoothly.
Next move the Choke to OFF. If engine falters, move choke
immediately
to FULL and then gradually
to 1/2 then to OFF.
7.
Disconnect
the power cord. Always unplug
from the outlet
first, and then from the snow thrower.
Re(oil Starter
1.
2.
3.
4.
5.
6.
7.
Move the choke lever to FULL choke position
(cold engine
start).
If the engine
is warm, place the choke in OFF position
instead
of FULL.
Push the Primer three (3) times, making
sure to cover the
vent hole when pushing.
If the engine
is warm, push the primer button
only once.
NOTE: Always cover the vent hole in the primer
button
when pushing.
Additional
priming
may be necessary for
first start if temperature
is below
15 degrees
Fahrenheit.
Grasp the starter handle and pull the rope out slowly, until
it pulls slightly
harder. Let the rope rewind
slowly.
Pull the starter handle
rapidly. Do not allow the handle to
snap back. Allow it to rewind
slowly while keeping
a firm
hold on the starter handle.
As the engine
warms up and begins to operate evenly,
rotate the choke lever slowly to the 1/2Choke position.
When the engine
begins to run smoothly,
move the choke
to the OFF position.
If the engine falters, return to FULL
choke, then slowly move to 1/2then OFF position.
Stopping the Engine
1.
Run the engine for a few minutes
before stopping
to help
dry offany
moisture
on the engine.
2.
To stop the engine, turn the ignition
key to the OFF/STOP
position
3.
Remove the ignition
key and store it in a safe place.
4.
Wipe all the snow and moisture
from the area around
the
engine.
NOTE: Excessive upward
pressure on the handle will result
in premature
wear on the rubber
auger blades which
would
not be covered
by warranty.
_
WARNING!
Muffler,
engine and surrounding
areas
become
hot and can cause a burn. Be careful and do
not touch when hot.
Engaging the Augers
1.
Engage the auger by squeezing
the auger control
against
the upper handle. Release to stop the augers.
Engaging the Drive
Lift up slightly
on the handle to allow the rubber
paddles
on the auger to contact
the pavement
and propel
the snow
thrower
forward.
Pushing downward
on the handle will
raise the augers offthe
ground and stop forward
motion.
'°1
Publicidad
