Publicidad
Idiomas disponibles
Idiomas disponibles
Failure to comply with these instructions may
result in a hazardous situation which, if not
avoided, may result in injury.
Spiders
and small insects can spin webs and
nest in the grill
during transit and
warehousing
as flow
obstruction
_round the
Burner
FIRE"
can
an
unsafe
To
FIRE
bes
as folb
3 this
at least
or
whenever
_, and if
your grill h_
period
of time
1. Remove the screws
the rear of each Main
Burner using a Phillips Head Screwdriver.
2. Carefully lift each Burner up and away from the
Gas Valve Orifice.
3. Check and clean Burner/Venturi
Tubes for
insects and insect nests. A clogged tube can
lead to a fire beneath the grill.
4. Refer to the figure below and perform one of
these
3 cleaning
methods:
[]
METHOD
1: Bend a stiff wire or wire coat
hanger
into a small hook
as shown
and run
the hook through
the Burner Tube and inside
the Burner several times to remove debris.
J
TO CLEAN BURNER TUBE,
INSERT HOOK
HERE
Burner Port
/
Foot
/
\
........................
d ......................
""Burner
Tube
[]
METHOD
2: Use a bottle brush with a flexible
handle and run the brush through
the Burner
Tube and
inside the Burner several times to
remove any debris.
[]
METHOD
3: Use an air hose to force air
through
each Burner Tube.
The forced
air
should
pass debris
or obstructions
through
the Burner and out the Ports.
For safe operation
ensure
the Gas Valve Assem-
bly Orifice is inside the Burner Tube
before using
your grill. See figure.
If the Orifice is not inside
the Burner Tube,
lighting
the Burner may cause
explosion
and/or
fire resulting
in serious
bodily
injury and/or
property
damage.
Gas Valve Assembly
Orifice
Burner Tube
To expedite the assembly process follow these
general guidelines:
[]
Tools
Required
for Assembly
:
• protective work gloves
• Phillips Head Screwdriver
[]
You will need assistance from another
person to
handle
this grill and island.
[]
[]
This grill island is shipped in two cartons. You will
need both
cartons to complete
assembly.
Use the Hardware and Part Diagrams to ensure all
items are included and free of damage.
[]
Do not assemble or operate the grill if it appears
damaged.
If there are damaged or missing parts
when you unpack the shipping box or you have
questions during the assembly process, call the:
Grill Information
Center
1-888-317-7642
8am-8pm
CST, Monday
throuqh
Friday
Grill Installation Codes
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA
54, Storage and Handling of
Liquefied Petroleum
Gases, ANSI/NFPA58,Natural
Gas
and Propane Installation Code, CSA B149.1, Propane
Storage and Handling Code, B149.2.
.
.
Do not store or use gasoline
or
other flammable
liquids or vapors in
the vicinity
of this or any other
appliances.
An LP cylinder
not connected
for
use shall not be stored in the vicin-
ity of this or any other appliance,
When
using electrical
appliances,
basic
safety precautions
should
always
be used.
This appliance, when installed, must be electri-
cally grounded
in accordance
with local codes
or, in the absence
of local
codes,
with the
National Electrical Code, ANSI/NFPA
70, or the
Canadian Electrical
Code, CSA C22. 1.
• Keep any electrical
supply cord and the fuel
supply hose away from any heated surfaces.
Publicidad
