Black and Decker Smartselect BDPH200B Manual De Instrucciones página 17

60°C (140°F) . Flashpoint is the temperature that a
fluid can produce enough vapors to ignite (see coating
supplier).
f Make sure clean up area is well ventilated and free of
flammable vapors.
f Always spray outdoors when spraying cleaning
solution through sprayer.
f Do not submerse power unit.
To begin cleaning:
f Unplug the cord from the power source.
f Unscrew the lid from the side of the canister and pour
any remainingliquid back into the original container
(Fig. I).
f Pour a small amount of the appropriate cleaning
solution into the canister (Fig. J).
f Warm soapy water for water based materials
f Manufacturers recommended cleaning solution for
oil based materials
f Replace the lid on the canister securely and vigorously
shake the sprayer.
f Unscrew the lid from the side of the canister and
properly dispose of cleaning solution.
f Refill the canister with a small amount of new
cleaning solution (Fig. J). Screw lid securely on
canister.
f Plug in the power cord.
f Spray the cleaning solution through the sprayer onto
scrap material for 2 to 3 seconds (Fig. K).
f Unplug the cord from the power source.
f Remove the canister and unscrew the side lid.
Remove the check valve, pickup tube and o-ring from
the sprayer (Fig. L). Clean the parts with the cleaning
brush in the appropriate cleaning solution
f Unscrew the tip collar and remove the spray nozzle
and spray tip (Fig. M). Clean all parts with the
cleaning brush in the appropriate cleaning solution.
f Separate the nozzle section from the sprayer motor by
pressing the release button on the motor housing as
shown in Fig. N.
f Grasp the nozzle section and twist until it is 90 degrees
to the housing, then pull straight out (Fig. O).
f If using water based material, clean the nozzle section
by running water through pickup tube inlet as shown in
Fig. P. If using oil based materials, clean pickup tube
inlet with the appropriate cleaning solution. Repeat
until sprayer is completely clean.
f Dry all parts thoroughly.
f Properly dispose of cleaning solution.
f Place a drop of household oil onto the metal ball in the
check valve (Fig. Q).
Important!: Lubricating the ball in check valve,
after cleanup, will help to prevent it from sticking
which can clog the valve and prevent adequate
PORTUGUÊS • 17
flow of spray material.
f Note: When reassembling, place metal ball end of
check valve into sprayer.
f Reassemble sprayer (Fig. R).
Note: The spray tip can only go in one way. The notch
on the spray tip, shown in Figure S must align with
the recess in the threads of the sprayer.
f Align the nozzle section 90 degrees to the motor
housing and press it fully into the motor housing as
shown in Fig. T.
f Grasp the nozzle section and twist it downward until
the pointer on the nozzle section aligns with the lock
symbol on the motor housing (Fig. U).
When properly connected, the two pieces will "snap"
into place.
MAINTENANCE AND STORAGE
Use only mild soap and damp cloth to clean the power
unit. Never let any liquid get inside the power unit; never
immerse any part of the power unit into a liquid.
Important!: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment (other
than those listed in this manual) should be performed
by authorized service centers or other qualified service
organizations, always using identical replacement parts.
The sprayer contains a washable/reuseable filter (Fig. V).
Check the filter before and after each use. If dirty, wash
with warm water and allow to air dry before re-installing or
replace if necessary.
f To check the filter, remove the filter cover by
loosening the two screws in the cover and pulling the
cover off the sprayer. Remove the filter as shown in
figure V and inspect. Replace filter and filter cover.
Snugly tighten screws. Never operate the sprayer
without the filter in place. Debris could be sucked in
and interfere with the function of the sprayer.
Make sure unit is clean and dry before storing. Store unit
indoors in a dry location. To prevent damage, wrap the
electrical cord so that it is not crimped during storage.
ACCESSORIES
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
Warning! The use of any accessory not recommended
for use with this product could be hazardous.