DeWalt DWE7485 Manual De Instrucciones página 14

English
3. Feed the workpiece through until the edge of the material reaches the front edge of the saw
table top.
4. Continue feeding the material using the push block
Push Block (Fig. BB, CC)
iMPORTAnT: Only use the push block 58
Rip Auxiliary Fence. The push block should be used once the material being cut reaches the saw
table top.
1. Construct a push block using the diagram in Figure BB.
nOTE: Edges
45 must be parallel.
iMPORTAnT: The over hanging edge
47
cause the push block to slip or push the material away from the fence.
Fig. BB
4-3/4"
5"
(121 mm)
(127 mm)
45
12"
1/2"
(305 mm)
(12.7 mm)
2-1/2"
(64 mm)
5-1/4"
1/2"
(133 mm)
(12.7 mm)
2. Place the push block 58 (Fig. CC) behind the material and ensure the lip of the block is flush
to the narrow rip auxiliary fence .
55
3. Once the push block is in place, continue feeding the material until the cut is complete
making sure the push block remains flush to the narrow rip auxiliary fence at all times.
iMPORTAnT: The narrow rip auxiliary fence and the over hanging edge
be the same thickness.
Fig. CC
Featherboard Construction (Fig. DD, EE)
Featherboards are used to keep the work in contact with the fence and table, and help prevent
kickbacks. Dimensions for making a typical featherboard are shown in Figure DD. Make
the featherboard from a straight piece of wood that is free of knots and cracks. Clamp the
featherboard to the fence and table so that the leading edge of the featherboard will support the
workpiece until the cut is complete (Fig. EE). An 8" (203 mm) high flat board can be clamped to
the rip fence and the featherboard can be clamped to the 8" (203 mm) high board.
Fig. DD
24" (610 mm)
The kerf should
be about 1/4"
4"
(6.4 mm) apart
(102 mm)

WARNING: Use featherboards for all non-through-cutting operations where the blade
guard assembly, anti-kickback assembly and riving knife cannot be used. Always replace
the blade guard assembly, anti-kickback assembly and riving knife when the non-
through-cutting operation is complete. Make sure the featherboard presses only on the
portion of the workpiece in front of the blade.
12
58 until the cut is complete.
with the narrow rip auxiliary fence, refer to Narrow
(Fig. BB) MUST be square. An uneven lip could
1/2"
(12.7 mm)
47 (Fig. BB) should both
58
55
5" (127 mm)
Fig. EE
MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect
it from power source before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can cause injury.
Cleaning
58

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
47
immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
D WALT call 1-800-4-D WALT (1-800-433-9258) or visit our website: www.dewalt.com.
e e
• Compatible Stands (DW7440RS, DW7451, DWE74911**)
• Dust extraction Y connector (contact your local dealer)
** The DWE74911 stand is ONLY compatible with the DWE7485 if purchased separately. When
purchased with the original DWE7491RS saw, the stand DOES NOT include the necessary
adapter brackets for the DWE7485.
Repairs

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including power cord repairs, and brush inspection and replacement, when
applicable) should be performed by a D
service center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will help you obtain more efficient warranty
service in case there is a problem with your product.
•
COnFiRMATiOn OF OWnERshiP: In case of an insurance loss, such as fire, flood or theft,
your registration of ownership will serve as your proof of purchase.
•
FOR YOUR sAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com
Three Year Limited Warranty
3/4"
D WALT will repair or replace, without charge, any defects due to faulty materials or
e
(20 mm)
workmanship for three years from the date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair
information, visit www.dewalt.com or call
1-800-4-D WALT (1-800-433-9258). This warranty does not apply to accessories or damage
e
caused where repairs have been made or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damages, so these limitations may not apply
to you. This warranty gives you specific legal rights and you may have other rights which vary in
certain states or provinces.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of your D
for any reason, you can return it within 90 days from the date of purchase with a receipt for a full
refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning labels become illegible or are missing,
call 1-800-4-D WALT (1-800-433-9258) for a free replacement.
e
WALT, have not been tested
e
WALT factory service center or a D WALT authorized
e e
WALT Power Tool or Nailer
e