Publicidad
Idiomas disponibles
Idiomas disponibles
OWNER'S MANUAL | USING YOUR BLACKSTONE
IGNITIoN INSTRUCTIoNS
1. CHECK VALVES
Turn knob to oFF position�
STEP 01
Push in knob and release� Knob should spring back�
STEP 02
If knobs do NoT
If knobs
do NoT spring back, replace valve assembly before using appliance.
spring back, replace valve assembly before using appliance.
Rotate knob to loW then turn back to oFF� Knob should
STEP 03
turn smoothly�
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
light burners and rotate knobs from HIGH to loW�
STEP 01
look below the cooking surface to view burners� When knob
STEP 02
is at HIGH, flames should be larger than when knob is at loW�
HEALTHY FLAME PATTERN
❶ ❶
❷ ❷
❸ ❸
❶ ❶
Flickers of yellow color.
Flickers of yellow color.
❷ ❷
dark blue color.
dark blue color.
❸ ❸
Vibrant blue.
Vibrant blue.
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
light burner and rotate knob from loW to HIGH�
STEP 01
look below the turntable to view burner� When knob is at
STEP 02
10
HIGH, flames should be larger than when knob is at loW�
YELLOW OR IRREGULAR
If there is a sudden drop or low
If there is a sudden drop or low
flame issue, please reference the
flame issue, please reference the
Troubleshooting chapter.
Troubleshooting chapter.
2. PIEZO-ELECTRIC GRIDDLE IGNITION
2. THERMOCOUPLE SURE-START IGNITION
do NoT lean over the appliance while lighting�
Keep the oven door closed as much as possible to reach and
maintain temperature�
ensure there is one (1)
❶
❶ Push the control knob in to
STEP 01
AA battery (not included) under
start gas flowing�
the battery cap�
❷ ❷ Turn the control knob
counter-clockwise to activate
STEP 02
the starter�
❶ ❶ Turn the Pizza oven control knob to oFF�
❸ ❸ Adjust the temperature to
❷ ❷ Turn on the motor�
desired level�
❸ ❸ Push in the control knob and turn counterclockwise a quarter
turn to loW� Hold in for 10~20 seconds until thermocouple heats
up� You should hear the igniter clicking the entire time� (When you
release the knob, the oven should remain lit�)
once the flame is consistent, adjust to desired
STEP 03
temperature ❹.
❹.
❶ ❶
❸
❸
❹ ❹
Before first use, run the oven for 15-20 minutes on HIGH to burn off manufac-
Before first use, run the oven for 15-20 minutes on HIGH to burn off manufac-
turing remnants.
turing remnants.
IF IGNITION DOES NOT OCCUR IN 5 SECONDS:
Turn the burner control knob oFF�
STEP 01
Wait 5 minutes�
STEP 02
Repeat the lighting procedure�
STEP 03
If burner does not ignite, please reference the Troubleshooting chapter.
If burner does not ignite, please reference the Troubleshooting chapter.
IF IGNITION DOES NOT OCCUR IN 5 SECONDS:
Turn the burner control knob oFF�
STEP 01
Wait 5 minutes�
STEP 02
Repeat the lighting procedure�
STEP 03
If burner does not ignite, please reference the Troubleshooting chapter.
If burner does not ignite, please reference the Troubleshooting chapter.
Model: 2238
❶ ❶
❷ ❷
❸ ❸
❷ ❷
BLACKSTONEPRODUCTS.COM/SUPPORT
2. TH
Rem
while
STEP 0
batter
batter
Screw
positiv
STEP 0
contro
STEP 0
cylind
oPd h
wise 1
Tighte
regula
positio
half tu
STEP 0
counte
until th
entire
once t
For pre
For pre
knob on
knob on
Publicidad
