Publicidad
Idiomas disponibles
Idiomas disponibles
turn off, press the main power switch
again (See Fig. A).
d. To prevent the switch trigger from being
accidentally pulled, a lock-off lever is
provided. To start the tool, depress the
lock-off lever (9) and pull the switch
trigger (11) (See Fig. D).
e.
Release the switch trigger to stop.
Checking the chain brake
8.5
(See Fig. E).
Caution! Should the saw chain not stop
immediately when this test is performed,
the saw may not be used under any circum-
stances. Consult our authorized service
centre.
a. Press the main power switch (17)until
the main power lamp lights (16) up.
b. Depress the lock-off lever (9), then pull
the switch trigger (11). The saw chain
starts immediately.
Push the front hand guard (2) forwards
c.
with the back of your hand. Make sure
that the chain saw comes to an imme-
diate standstill.
Checking the run-down brake
8.6
Caution! If the saw chain does not stop
within one second in this test, stop using
the chain saw and consult our authorized
service centre.
a. Press the main power switch (17) until
the main power lamp (16) lights up.
b. Depress the lock-off lever (9), then pull
the switch trigger (11). The saw chain
starts immediately
c.
Release the switch trigger completely.
The saw chain must come to a stand-
still within one second.
Working with the chain saw
8.7
Caution!
• The first time user should, as a minimum
practice, do cutting logs on a saw-horse
or cradle.
• When sawing precut timber, use a safe
support (saw horse or cradle). Do not
steady the workpiece with your foot, and
do not allow anyone else to hold or
steady it.
• Secure round pieces against rotation.
7064196-36V-Chainsaw-Ma-2202-22.indb 11
7064196-36V-Chainsaw-Ma-2202-22.indb 11
• Keep all parts of the body away from the
saw chain when the motor is operating.
• Hold the chain saw firmly with both
hands when the motor is running.
• Do not overreach. Keep proper footing
and balance at all times.
NOTICE:
• Never toss or drop the tool.
• Do not cover the vents of the tool.
Bring the bottom edge of the chain saw
body into contact with the branch to be cut
before switching on. Otherwise it may
cause the guide bar to wobble, resulting in
injury to operator. Saw the wood to be cut
by just moving it down by using the weight
of the chain saw (See Fig. O).
If you cannot cut the timber right through
with a single stroke: Apply light pressure to
the handle and continue sawing and draw
the chain saw back a little; then apply the
spike bumper a little lower and finish the cut
by raising the handle (See Fig. P).
Bucking
8.8
(See Fig. P).
a. Rest the bottom edge of the chain saw
body on the wood to be cut.
b. With the saw chain running, saw into
the wood while using the rear handle to
raise the saw and the front one to guide
it. Use the spike bumper as a pivot.
c.
Continue the cut by applying slight
pressure to the front handle, easing the
saw back slightly. Move the spike
bumper further down the timber and
raise the front handle again.
NOTICE: When making several cuts, switch
the chain saw off between cuts.
Caution! If the upper edge of the bar is used
for cutting, the chain saw may be deflected
in your direction if the chain becomes
trapped. For this reason, cut with the lower
edge, so that the saw will be deflected away
from your body (See Fig. V).
Changing the saw chain
8.9
• Only handle the saw chain with gloves
and remove the battery first!
• Inspect the saw chain and the guide bar
for damage or signs of wear.
English
11
09-05-2022 15:33
09-05-2022 15:33
Publicidad
