Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Installing the charging base
-
Place the charging base against a wall and leave a minimum free space of 1.5 metres to the
front and 0.5 metres to each side. Fig. 7
-
Connect the charging base to a power socket. Wind and store the remaining cable to
prevent accidents.
-
Hold down the Start/Pause button for a few seconds.
-
When the indicator light turns on, place the robot vacuum cleaner in the charging base
and make sure the charging terminals on the robot match those of the charging base. If
the light is flashing blue, it means the battery is not completely charged. To ensure the
maximum cleaning time, wait until the light turns into steady blue, as this indicates that
the battery is fully charged and that the robot vacuum cleaner is ready to clean.
Note
-
Take the robot vacuum cleaner to the charging base if the battery is low. The robot vacuum
cleaner may not turn on if battery is too low.
-
The robot vacuum cleaner will automatically turn on when placed on the charging base.
-
The robot vacuum cleaner cannot be turned off during recharge.
Installing the clean-water tank. Fig. 8
-
Pull out the clean-water tank (tank with transparent lid) in the direction shown.
-
Lift up the lid and fill the water tank with clean water Do not exceed the "MAX" mark on
the tank.
-
Install again the clean-water tank in its original position
Recommendations
Add a few drops of cleaning agent to the water if necessary, as long as it is non-corrosive.
Using cleaning agents in excess might block water outlets.
In order to achieve perfect scrubbing, it is suggested to moisten the mop before using it and
washing it after each use
First use
-
Once the robot vacuum cleaner and the charging base are installed, follow these steps
before the first cleaning.
-
First of all, fully charge the robot vacuum cleaner. It is suggested to allow the robot to
charge overnight. Once fully charged, it may carry out the first cleaning cycle and save
the first map. To do so, activate the Auto mode and select the Eco suction level. It is very
important to follow these instructions so that the robot vacuum cleaner recognises every
corner of your house and can carry out a complete mapping of it.
-
If your house is very large and the robot vacuum cleaner runs out of battery, it will return
to the charging base, save both complete and incomplete maps, and, once charged, it will
54
CONGA 11090 SPIN REVOLUTION HOME&WASH
resume cleaning where it left off until the entire surface has been mapped. The robot
vacuum cleaner is constantly mapping, so it adapts in an individualised and personalised
way to the particularities of each house while constantly improving its map.
-
The robot will return to the charging base to clean the mops and moisten them again to
continue cleaning, according to the frequency selected in the application.
Information on the charging base
-
After cleaning, the robot will automatically return to the self-emptying base to recharge
the battery and empty the dirt tank.
-
During cleaning, the robot will return to the charging base to clean the mops and moisten
them again to continue cleaning where it left off, depending on the frequency selected
in the app. The base will perform the self-emptying function according to the emptying
frequency value selected on the app.
-
In addition, it is possible to force the emptying of the dust tank from the robot vacuum
cleaner by pressing the "home" return-to-base button, or from the app.
-
When the robot vacuum cleaner reaches the charging base it will beep once, indicating that
it has made good contact with the charging terminals of the base.
-
The base will then clean the mops and collect the dirty water generated. After cleaning and
dirty water collection, the base will activate the mop drying function.
-
If the indicator light on the charging base is red, it may indicate that the dirt bag is not
attached or is full, the clean-water tank is empty or the dirty water tank is full.
-
If so, fit or replace the bag, fill the clean-water tank or empty the dirty water tank.
3. OPERATION
Robot vacuum cleaner's buttons
Auto Mode
-
Press the Start/Pause button on the robot vacuum cleaner or from the app for the robot
to automatically start cleaning in Edge mode and perform a cleaning cycle in an orderly
zig-zag pattern, while recognising which areas it has cleaned and which it hasn't. The
robot vacuum cleaner will automatically plan the cleaning route during cleaning.
-
The robot will return to the charging base to clean the mops and moisten them again to
continue cleaning, according to the frequency selected in the application.
-
If you control the robot vacuum cleaner manually during this mode, the robot will
recalculate the route, so it may pass through already cleaned areas. To ensure efficient
cleaning, do not operate the robot vacuum cleaner manually during automatic cleaning.
-
Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle,
the robot vacuum cleaner will smartly return to the charging base automatically and once
fully charged, it will resume the cleaning process from the same point.
-
During cleaning, the robot vacuum cleaner will stop briefly to evaluate the area and
calculate the cleaning route (this stop will vary depending on the house conditions).
ENGLISH
CONGA 11090 SPIN REVOLUTION HOME&WASH
55
Publicidad
