EINHELL TC-TS 2225 U Manual De Instrucciones Original página 26

2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Saw blade guard / splitter
•
Push stick
•
Parallel stop
•
Hand wheel
•
Crank arm
•
Rubber foot (4x)
•
Cross stop
•
Screw for parallel stop (2x)
•
Stop rail for parallel stop
•
Knurled screw (2x)
•
Leg (4x)
•
Cross strut (4x)
•
Locking screw for table width extension (4x)
•
Locking screw for table length extension (2x)
•
Table width extension (left)
•
Table width extension (right)
•
Table length extension
•
Additional leg (2x)
•
Wrench, size 10/13 mm
•
Wrench, size 10 mm
•
Hexagon screw M6x16 (8x)
•
Washer, large (12x)
•
Lock bolt (16x)
•
Washer, small (20x)
•
Spring washer (16x)
•
Nut (20x)
•
Recessed head screw (6x)
•
Strut for base frame (2x)
•
Hexagon screw M6x45 (4x)
Anl_TC-TS_2225_U_SPK13.indb 26
GB
•
Hexagon screw M6x12 (5x)
•
Self-locking nut
•
Original operating instructions
•
Safety information
3. Proper use
The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross
stop) of all types of timber commensurate with the
machine's size. The equipment is not to be used
for cutting any type of round wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The equipment is to be operated only with suita-
ble saw blades (saw blades made of HM or CV)
It is prohibited to use any type of HSS saw blade
and cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
- 26 -
31.01.2024 10:33:30