Metabo WPB 36 LTX BL 230 Manual Original página 12

en ENGLISH
Other accessories:
(see also www.metabo.com)
A Chargers
Best.-Nr.: 627378000 ASC 145
Best.-Nr.: 627265000 ASC Ultra
Best.-Nr.: 627495000 ASC 145 Duo
B Battery pack 18 V
Best.-Nr.: 625368000 5,5 Ah LiHD
Best.-Nr.: 625369000 8,0 Ah LiHD
DS
Best.-Nr.: 624990000 5,5 Ah LiHD
C Adjusting nut (9)
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to power tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste! Please return faulty or used battery packs to
your Metabo dealer!
Do not throw battery packs into water.
14. Technical Data
Explanatory notes on the specifications on page 2.
Changes due to technological progress reserved.
U = Battery pack voltage
Dmax = max. diameter of accessory
tmax,1 = max. permitted thickness of clamping
shank on accessory when using clamping
nut (9)
tmax,3 = grinding wheel/cut-off wheel:
max. permitted thickness of accessory
t = max. permitted thickness of wheel-type
max,4
wire brushes
M = Spindle thread
l = Length of the sanding spindle
n = No-load speed (maximum speed)
0
P1 = Rated input power
P2 = Power output
m = Weight (with the smallest battery pack)
12
Permitted ambient temperature during operation:
-20 °C (-4°F) to 50 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C (32°F) to
30 °C (86°F).
Recommended ambient temperature when
charging: 32°F (0°C) to 104°F (40 °C)
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods for assessment
purposes when the load is lower. Arrange protective
measures for the user, such as organisational
measures based on the adjusted estimates.
The grinding of thinner metal sheetsd other
workpieces with large surfaces that easily vibrate
can lead to a significantly higher overall sound
emission (up to 15 dB) than the sound emission
values specified. The sound radiation of such
workpieces should be prevented to the greatest
extent possible by means of suitable measures,
such as fitting heavy, flexible damping mats. The
increased sound emission must also be taken into
account when assessing the risk of noise exposure
and selecting suitable hearing protection.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841
:
ah, SG = Vibration emission value (surface
grinding)
ah, DS = Vibration emission value (disc
sanding)
Kh,SG/DS = Uncertainty (vibration)
Typical A-weighted sound levels:
LpA = Sound pressure level
LWA = acoustic power level
KpA, KWA = Uncertainty
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!