Descargar Imprimir esta página

Kärcher LTR 3-18 Dual Manual Del Usuario página 18

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device does not start
up
The device stops during
operation
Warranty
The warranty conditions issued by our sales company
responsible apply in all countries. We shall remedy pos-
sible malfunctions on your device within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Technical data
Device performance data
Working voltage of the battery
Working width
Cutting string, diameter
no-load- speed
Determined values in acc. with EN 50636-2-91
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
wA
Uncertainty K
WA
Front handle with string reel hand-
arm vibration value
Rear handle with string reel hand-
arm vibration value
Front handle with blade hand-arm
vibration value
Rear handle with blade hand-arm
vibration value
Uncertainty K
18
Troubleshooting guide
Cause
One or both battery packs is not fitted
correctly.
One or both battery packs is empty.
One or both battery packs is defective.
String is too long and is causing the mo-
tor to overload
Cutting head blocked by cutting residue  Remove the cutting residue.
Motor is overloaded
Motor has overheated
The battery has overheated
One or both battery packs is empty.
LTR 3-18
Dual
V
36
mm
300
mm
2,00
-1
min
max. 8000
dB(A)
82,2
dB(A)
3
dB(A)
94,6
dB(A)
3
2
m/s
3,93
2
m/s
1,56
2
m/s
5,89
2
m/s
3,48
2
m/s
1,5
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Push the battery packs into the mounting
until they latch into place.
 Check which battery pack is empty and
charge it.
 Replace the defective battery pack.
 Install the string guard.
The string will automatically be shortened.
 Mow only suitable cutting material, see
Chapter Intended use.
 Stop working and allow the motor to cool
down.
 Stop working and allow the battery to cool
down to normal battery temperature.
 Check which battery pack is empty and
charge it.
Dimensions and weights
Length x width x height
Weight (without battery pack)
Subject to technical modifications.
Vibration value
WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Device with a hand-arm vibration value
> 2.5 m/s² (see chapter Technical Data in the
operating instructions)
CAUTION
for several hours can lead to numbness. ● Wear warm
gloves to protect your hands. ● Take regular breaks
from work.
Declaration of Conformity
EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
English
LTR 3-18
Dual
1020 x 
mm
310 x 920
kg
2,42
● Uninterrupted use of the device

Publicidad

loading