Hendi 222829 Manual Del Usuario página 13

cord. A frayed or damaged cord can expose users to great risk
of electric shock.
• If the device shows anomalies, do not use it or try to repair it:
please contact the supplier.
• Do not use the appliance for frozen foods or any products
other than food.
• Do not wear loose fitting clothing such as scarf, etc and long
hair should be tied up and keep away from the moving parts.
The manufacturer and/or the seller are not responsible in the
following cases:
- if the appliance has been handled by unauthorised personnel;
- if some parts have been replaced with non-original spare
parts;
- if the instructions included in this manual are not followed
precisely;
- if the cutter has not been cleaned and oiled with the right
products.
Safety system installed
Mechanical safety system
The appliance is equipped with 3 safety switches. The machine
only be started with all the safety switches are at the proper
positions:
• Bowl position safety switch: The machine can be started up
once the bowl is positioned at the correctposition.
• Bowl guard safety switch: The machine can only be started up
once the bowl guard is in the closed position.
• Lift up lever safety switch: The machine can only be started
up once the lift up lever is located in the upwards position.
Even though CE version appliances are provided with electrical
and mechanical protections (when the appliance is operating
and for maintenance and cleaning operations), there are still
RESIDUAL RISKS that cannot be eliminated completely; these
risks are specified in this manual under "WARNING! / DAN-
GER! / CAUTION! ". The moving parts of the machine can cause
injuries.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
Special safety features
ATTENTION: This machine has the following 3 safety switches.
The machine only be started with all the safety switches are at
the proper positions.
• Bowl position safety switch: The machine can be started up
once the bowl is positioned at the correct position.
• Bowl guard safety switch: The machine can only be started up
once the bowl guard is in the closed position.
• Lift up lever safety switch: The machine can only be started
up once the lift up lever is located in the upwards position.
• Do not wear loose fitting clothing such as scarf, etc and long
hair should be tied up and keep away from the moving parts
To avoid serious personal injury:
• DO NOT operate the machine without reading the instruction
manual.
• ALWAYS switch OFF the machine and unplug from electrical
power supply before cleaning, maintenance, repair or chang-
ing any attachments.
• ALWAYS keep hands, hair and loose clothing away from the
moving parts.
a) About the bowl guard
Note: When bowl guard is open or not properly closed in lock
position, the machine will not operate.
1. To open the bowl guard, hold the bowl guard handle and ro-
tate it clockwise. To close the bowl guard, hold the bowl guard
handle and rotate it anti-clockwise.
2. When the bowl guard handle is lined up at the right side of the
machine, the bowl guard is in the is in the rocked position and
ready for operation.
b) Install the bowl to the machine
Note: Install the bowl BEFORE fixing the attachments. Use the
supplied bowl only.
1. Lower the bowl by pulling the bowl lift-up lever downwards
until it stops. So that the bowl cradle is in a lower position.
2. Place the bowl carefully and slowly using the bowl handles
at 2 sides and
i) With the locking pin into the hole at the middle of the bowl
cradle and
ii) Align with guided pins on 2 sides of the bowl cradle.
c) Install different attachments (Flat beater, Dough hook or
Whisk) to the machine
Note: It is more convenient and easier to install the attach-
ments prior to adding the ingredients into the bowl.
1. Rotate the bowl guard clockwise gently, so that it is in the
open position.
2. CAUTION! Use excessive force to open or close the bowl
guard may damage the safety lock micro switch. Be careful
when open or close the bowl guard.
3. Slide the attachments (Flat beater, Dough hook or Whisk)
slowly upwards onto the planetary shaft fitting the shaft pin
through the slot in the attachments.
4. Rotate the attachments to secure it onto the planetary shaft.
GB
13