Hikmicro FT Serie Guia De Inicio Rapido página 6

a) The rechargeable lithium battery should be
installed on the device.
b) The device should keep working for more than 8
hours before shutting down.
4.1 Charge Device via Type-C Interface
Steps
1. Fold up the rubber cover.
2. Grip the ring-pull handle for interface and rotate it to
unlock, and pull out the interface cover.
3. Plug in the USB type-A to type-C cable, and charge the
device.
4. Put the interface cover in place, and grip the ring-pull
handle for interface and rotate it to lock the interface
cover.
5. Put back rubber cover on top.
4.2 Charge Device via Charging Base
Steps:
1. Remove the battery from the device.
1) Grip the ring-pull handle for battery, and rotate it
by 90° to unlock the battery.
2) Pull out the battery from the battery compartment.
2. Connect the charging base to power supply using the
supplied charging base power adapter.
3. Insert the battery into the charging base. You can see
the charging status via the indicators.
Note:
 The input voltage of the charging base should meet the
limited energy circuit (12 VDC, 2 A).
 Charging indicators for batteries statuses are as follows:
Solid Red: Charging normally;
①
charged; OFF: Charging exception.
③
 Charging base indicator statuses are as follows:
Red: Functioning properly;
4. When the battery is fully charged, draw the battery
from the charging base.
5. Align the ribbed piece on battery with the notch of the
device, and push the battery into the battery
compartment until it is in the locked position.
Charging
Indicators for
Batteries
Charging Base
Indicator
Solid Green: Fully
②
①
OFF: Not functioning.
②
6. Grip the ring-pull handle, and rotate it to lock the
battery.
User Manual
Legal Information
© 2023 Hangzhou Microimage Software Co., Ltd. All rights
reserved.
About this Manual
The Manual includes instructions for using and managing
the Product. Pictures, charts, images and all other
information hereinafter are for description and explanation
only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other
reasons. Please find the latest version of this Manual at the
HIKMICRO website (www.hikmicrotech.com).
Please use this Manual with the guidance and assistance of
professionals trained in supporting the Product.
Trademarks
are the properties of HIKMICRO in various jurisdictions.
Other trademarks and logos mentioned are the properties
of their respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH
ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE
PROVIDED "AS IS" AND "WITH ALL FAULTS AND ERRORS".
HIKMICRO MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR
PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR
OWN RISK. IN NO EVENT WILL HIKMICRO BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF
SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED
ON BREACH OF CONTRACT, TORT (INCLUDING
NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF
HIKMICRO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES OR LOSS.
Solid
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET
PROVIDES FOR INHERENT SECURITY RISKS, AND HIKMICRO
SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES
RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS
INFECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKMICRO WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH
ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE
4
and other HIKMICRO's trademarks and logos