Mitsubishi Electric MFZ-KA09NA Manual De Instalación página 3

1-3. SPECIFICATIONS
1-3-1. POWER SUPPLY AND INDOOR/OUTDOOR WIRE CON- Electrical specifications
NECTION MODEL MFZ-KAOQNA | MFZ-KA12NA | MEZ-KA18NA
¢ Power should be taken from an exclusive branched circuit.
¢ Wiring work should be based on applicable technical standards.
¢ Wiring connections should be made following the diagram. Power supply (V, PHASE, Hz) 208/230, 1, 60
* Securely tighten screws. UNIT AMPS (A) <15
Connecting wires and the ground wire
¢ Use solid conductor AWG14 or stranded conductor AWG 14.
¢ Use double insulated copper wire with 600 V insulation. Outside [Minimum walll Insulation
* Use copper conductors only.
Pipe diameter |
thickness |thickness}
|Sulation
* Follow local electrical codes. - material
inch (mm)
Note: For liquid | KAO9/12/18 | 1/4 (6.35) | 0.0315 (0.8) | 5/16 (8) | Heat resistant
When the indoor unit is powered from the outdoor unit, depending on local foam plastic
code, a disconnect switch (145A MAX) needs to be installed to a power supply For gas KA0S/2 3/8 (9.52) | 0.0345 (0.8) 15/16 (8) 0.045 Specific
circuit. KA18 1/2 (12.7) | 0.0315 (0.8) | 5/16 (8) | gravity
1-3-2. REFRIGERANT PIPES
* To prevent condensation, insulate the two refrigerant pipes.
¢ Refrigerant pipe bending radius must be 4 in. (100 mm) or more.
Z\ CAUTION
Be sure to use the insulation of specified thickness (table on the right). Exces-
sive insulation may cause incorrect installation of the indoor unit, and too little
insulation may cause condensate to form.
* The unit has flared connections on both indoor and outdoor sides.
* Remove the valve cover from the outdoor unit, then connect the pipe.
¢ Refrigerant pipes are used to connect the indoor and outdoor units.
¢ Be careful not to crush or over bend the pipe in pipe bending.
1-4. INSTALLATION DIAGRAM Use the wall Wal hole cover (D)
ACCESSORIES hole sleeve —-Ndoor unit Seal tho wall hole
Check the following parts before installation. (C) to prevent gap with putty (H).
<Indoor unit>
indoor/outdoor wait hole
i
connecting
sleeve (C)
Attach the p i p
(1) {Drain hose 4 : «| to wall with pipe
wire (A) from -
(2) |Remote controller holder 1 contacting fixing band (E).
(3) {Screws for (2) 3.5 x 16 mm (Black)} 2 metal parts in
(4) |Pipe cover 4 the wall and Cut off the Pipe fixing
(5) [Band 3 to protect the extra length. 2 band (E)
wiring from y
(6) {Battery (AAA) for (12) 2 rodents. :
(7) {Indoor unit mounting bracket 1 Fixing screw (F)
(8) [Fixing screws for (7) 4 * 25 mm 5
(9) | Wood screw for indoor unit fixation} 4
(10) | Washer of (9) 4 t——---~_ After the leak test, apply insulating material
(41) [Felt tape (For left or left-rear piping) | 4 tightly so that there is no gap.
(12)|Wireless remote controller 4
(13) [Air cleaning filter 1
When the piping is to be attached to a wall com-
PARTS TO BE PROVIDED prised of tin plate or metal netting, use chemically
AT YOUR SITE treated wooden piece 25/32 in. (20 mm) or thicker
(F) ipi i i
(A) lIndoor/outdoor unit connecting wire] 1 between the wall and the piping, or wrap insulation
BIE . : 1 vinyl tape 7 to 8 turns around the piping.
(B) jExtension pipe To use existing piping, perform COOL operation
(C) |Wall hole sleeve i for 30 minutes and pump down before removing
(D) |Wall hole cover i the old air conditioner. Remake flare according to
(E) |Pipe fixing band 2to5 yae—""|_ the dimension for new refrigerant.
(F) | Fixing screw for (E) 4 x 20 mm 2to5
(G) {Piping tape 1
(H) |Putty 1
Drain hose
(I) |(or soft PVC hose, 19/32 in. (15 mm) 4
inner diameter or hard PVC pipe VP16)}
(J) |Refrigeration oil 1
(K) |Power supply cord* 1
* Note:
Place indoor/outdoor unit connecting wire (A)
and power supply cord (K) at least 3 ft. (1m) Units should be installed by licensed contractor
away from the TV antenna wire. according to local code requirements.
En-2