Publicidad
Idiomas disponibles
Idiomas disponibles
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical
shock.
Before you move your convertible
refrigerator/freezer
into its final
location,
it is important
to make sure you have the proper electrical
connection.
Your convertible
refrigerator/freezer
is equipped
with a
longer power cord for easier placement
and movement.
Recommended
Grounding
Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical
supply
is required.
It is recommended
that a separate
circuit
serving
only your convertible
refrigerator/freezer
be provided.
Use an outlet
that cannot
be turned off by a switch.
Do not use an extension
cord.
NOTE:
Before performing
any type of installation,
cleaning,
or
removing
a light bulb, turn the lower compartment
control
to OFF,
and then disconnect
the convertible
refrigerator/freezer
from the
electrical
source. When you are finished,
reconnect
the convertible
refrigerator/freezer
to the electrical
source and reset the control
to
the desired setting.
TOOLS NEEDED:
¾d' hex-head
socket wrench,
#2 Phillips
screwdriver,
flat-blade
screwdriver,
s/_,, open-end
wrench,
flat
2" putty knife.
IMPORTANT:
•
Remove food and any adjustable
door or utility bins from doors.
•
If you only want to remove
and replace the doors, see "Remove
Doors and Hinges"
and "Replace
Doors and Binges."
•
All graphics
referenced
in the following
instructions
are included
later in this section after "Final Steps."
Remove Doors and Hinges
5/16" Hex-Head Hinge Screw
1.
Unplug
convertible
refrigerator/freezer
or disconnect
power.
2,
Open lower compartment
door and remove
base grille from the
bottom
front of the convertible
refrigerator/freezer.
See Base
Grille graphic.
3,
Close the lower compartment
door and keep both doors closed
until you are ready to lift them free from the cabinet.
NOTE:
Provide additional
support
for the doors while the hinges
are being moved.
Do not depend
on the door magnets
to hold
the doors
in place while you are working.
4.
Remove the parts for the top hinge as shown in Top Hinge
graphic.
Lift the upper compartment
door free from the cabinet.
5.
Remove the parts for the center hinge as shown
in the Center
Hinge graphic.
Lift the lower compartment
door free from the
cabinet.
6.
Remove
the parts for the bottom
hinge as shown in the Bottom
Hinge graphic.
IMPORTANT:
If you want to reverse your doors
so that they open in
the opposite
direction,
continue
with the "Reverse
Doors (optional)"
instructions.
If you are not reversing
the doors,
see "Replace
Doors
and Hinges".
Reverse
Doors
(optional}
Round-Head
Door Handle
Handle Screw
Screw Hole Plug
Cabinet
1. Remove sad' hex-head hinge screws from handle side and move
them to opposite side. See Graphic 1.
2, Remove cabinet hinge hole plugs from the cabinet top and move
them to opposite side hinge holes as shown. See Graphic 2.
Doors
1. Remove door stop from both the upper and lower compartment
doors and move to the other side. See Graphics 3 and 4.
Replace Doors and Hinges
NOTE: Graphic
may be reversed
if door swing is reversed.
1.
Replace the parts for the bottom
hinge as shown. Tighten
screws.
Replace the lower compartment
door.
NOTE:
Provide additional
support
for the doors while the hinges
are being moved.
Do not depend
on the door magnets
to hold
the doors
in place while you are working.
2.
Assemble
the parts for the center
hinge as shown and tighten all
screws.
See Center Hinge graphic.
Replace the upper
compartment
door.
3,
Assemble
the parts for the top hinge as shown.
See Top Hinge
graphic.
Do not tighten screws
completely.
4.
Line up the doors so that the bottom
of the upper compartment
door aligns evenly with the top of the lower compartment
door.
Tighten
all screws.
Final
Steps
1.
Check all holes to make sure that hole plugs and screws are in
place. Reinstall
top hinge cover. See Top Hinge graphic.
2.
Replace the base grille. See Base Grille graphic.
Electrical Shock Hazard
Plug into a grounded
3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow
these instructions can result in death,
fire, or electrical
shock.
3.
Plug into a grounded
3 prong outlet.
4.
Return all removable
door parts to doors and food to convertible
refrigerator/freezer.
Publicidad
