Descargar Imprimir esta página

HIKVISION DS-2CD6425G2-C1 Guia De Inicio Rapido página 47

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 53
region. The equipment shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as
vases, shall be placed on the equipment. Provide a surge
suppressor at the inlet opening of the equipment under
special conditions such as the mountain top, iron tower, and
forest. CAUTION: To reduce the risk of fire, replace only with
the same type and rating of fuse.
Battery
Do not ingest battery. Chemical burn hazard! This product
contains a coin/button cell battery. If the coin/button cell
battery is swallowed, it can cause severe internal burns in
just 2 hours and can lead to death. Keep new and used
batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it
away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek
immediate medical attention. CAUTION: Risk of explosion if
the battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions. ATTENTION: IL Y A
RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR
UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES
BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
Improper replacement of the battery with an incorrect type
may defeat a safeguard (for example, in the case of some
lithium battery types). Do not dispose of the battery into fire
or a hot oven, or mechanically crush or cut the battery,
which may result in an explosion. Do not leave the battery in
an extremely high temperature surrounding environment,
which may result in an explosion or the leakage of flammable
liquid or gas. Do not subject the battery to extremely low air
pressure, which may result in an explosion or the leakage of
flammable liquid or gas. + identifies the positive terminal(s)
of equipment which is used with, or generates direct
current. - identifies the negative terminal(s) of equipment
which is used with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles, should be
placed on the equipment. The serial port of the equipment
is used for debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned fingers when handling the
parts. Wait one-half hour after
switching off before handling parts.
This sticker is to indicate that the
marked item can be hot and should
not be touched without taking care. For device with this
sticker, this device is intended for installation in a restricted
access location, access can only be gained by service persons
or by users who have been instructed about the reasons for
the restrictions applied to the location and about any
precautions that shall be taken.
Installation
Install the equipment according to the instructions in this
manual. To prevent injury, this equipment must be securely
attached to the floor/wall in accordance with the installation
instructions. Never place the equipment in an unstable
location. The equipment may fall, causing serious personal
injury or death.
Power Supply
Device powered by Safety Extra-Low Voltage(SELV): The
power source should meet limited power source or PS2
requirements according to IEC 60950-1 or IEC 62368-1
standard.
Device powered by AC mains supply voltage: The equipment
must be connected to an earthed mains socket-outlet. An
appropriate readily accessible disconnect device shall be
incorporated external to the equipment. An appropriate
overcurrent protective device shall be incorporated external
to the equipment, not exceeding the specification of the
building. An all-pole mains switch shall be incorporated in
the electrical installation of the building. Ensure correct
wiring of the terminals for connection to an AC mains
supply. The equipment has been designed, when required,
modified for connection to an IT power distribution system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from this
product. DO NOT stare at operating light source. May be
harmful to the eyes. Wear appropriate eye protection or DO
NOT turn on the white light when you assemble, install or
maintain the camera.
Transportation
Keep the device in original or similar packaging while
transporting it.
System Security
The installer and user are responsible for password and
security configuration.
Maintenance
If the product does not work properly, please contact your
dealer or the nearest service center. We shall not assume
any responsibility for problems caused by unauthorized
repair or maintenance. A few device components (e.g.,
electrolytic capacitor) require regular replacement. The
average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and
outside surfaces of the product cover. Do not use alkaline
detergents.
Using Environment
When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may burn
out. DO NOT expose the device to high electromagnetic
radiation or dusty environments. For indoor-only device,
place it in a dry and well-ventilated environment. DO NOT
aim the lens at the sun or any other bright light. Make sure
the running environment meets the requirement of the
device. DO NOT place the camera in extremely hot, cold,
dusty or damp locations, and do not expose it to high
electromagnetic radiation.
Emergency
4

Publicidad

loading

Este manual también es adecuado para:

Ds-2cd6425g2-c2Ds-2cd6445g2-c1/hdmi