Würth TG 12-A Instrucciones De Servicio Originales página 21

Technical Data
Cordless Cutter
Article number
Rated voltage
A)
Rated speed
Max. grinding disc diameter
Mounting diameter
Weight according to EPTA-Pro-
B)
cedure 01:2014
Recommended ambient temper-
ature during charging
Permitted ambient temperature
C)
during operation and during
storage
Recommended rechargeable
batteries
Recommended chargers
A) Rated speed in accordance with EN 60745-2-3
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically, the A-weighted sound pressure level of the power
tool is 75 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing
protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 13.5 m/s , K = 1.5 m/s ,
h
The vibration level given in these instructions has been meas-
ured in accordance with a standardised measuring procedure
and may be used to compare power tools. It can also be used
for a preliminary estimation of exposure to vibration.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for different
applications, with different application tools or poorly main-
tained, the vibration level may differ. This can significantly in-
crease the exposure to vibration over the total working period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not actu-
ally being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the operator
from the effects of vibration, such as servicing the power tool
and application tools, keeping the hands warm, and organ-
ising workflows correctly.
TG 12-A
5700 135 000
V= 12
-1
min 19,500
mm 76
r
mm 10
kg 0.70–0.90
Note: The battery is supplied partially charged. To ensure full
battery capacity, fully charge the battery in the charger before
°C 0 to+35
using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
°C –20 to +50
ducing its service life. Interrupting the charging process does
not damage the battery.
The lithium-ion battery is protected against deep discharge by
LI-ION
the "Electronic Cell Protection (ECP)". When the battery is dis-
12V/2,0Ah
charged, the power tool is switched off by means of a protect-
AL 40-LI
ive circuit: The application tool no longer rotates.
r
Follow the instructions on correct disposal.
To remove the battery (4), press the release buttons (5) and
pull the battery out of the power tool. Do not use force to
do this.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slowly flashing light 1 x green
r
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Application
Service" section for addresses.
Fitting
Charging the battery
Use only the chargers listed in the technical
data. Only these chargers are matched to the lithium-ion
battery of your power tool.
Do not continue to press the On/Off switch after
the power tool has automatically switched off.
The battery can be damaged.
Removing the Battery (see figure A)
Battery charge indicator
Fitting Protective Equipment
Remove the battery from the power tool before
carrying out work on the power tool (e.g. main-
tenance, changing tool, etc.). The battery should
also be removed for transport and storage.
There is risk of injury from unintentionally pressing the on/
off switch.
Capacity
60–100%
30–60%
10–30%
0–10%
21