Publicidad
Idiomas disponibles
Idiomas disponibles
:e
exists that icing may occur, the unit should
cn
be set to operate in anti-freeze mode before
::J
use. (F15}
HOW TO SWITCH BETWEEN OPERATING
�
W
MODES (F15)
1. Flip the engine switch to turn off the
engine.
2. Remove the air cleaner cover form the
cylinder cover
3. Loosen a screw and remove the screen
on the back of the air cleaner cover.
4. Reattach the screen right side left so as to
the anti-icing plate if on the right. Reinstai!
the cover.
(1) Air cleaner ccver, (2) Anti-icing plate
(3) Screw, (4) Normal operaling mode
(5) Anti-freeze moda, (6) Screen
..&.
WARNING
Continuing to use the product in anti-freeze
mode even when temperaturas have risen
and returned to normal may result in the
engine falling to
start properly or in the engine falling to
operate at its normal speed. And for this
reason you should always be sure to return
the unit to normal operating mode if there is
no danger of icing occurring.
When using the saw with the anti-freeze
mode, frequently check the screen and keep
it clean of saw dust.
CHAIN BARKE (F17)
This machine is equipped with an automatic
brake to stop saw chain rotation upon
occurrence of kickback while in saw cutting
operated. by inertial force which acts on the
weight fitted inside the front guard.
This brake can also be operated manually
with the front guard turned down to the guide
bar.
To release brake. pull up the front guard
toward the front handle till "click" sound is
heard.
Caution
Be sure to confirm brake operation on the
daily inspection.
How to confirm:
1. Turn off the engine.
2. Holding the chain saw horizontally. release
your hand from the front handle. hit the
tip of the guide bar to a stump or a piece
of wood. and confirm brake operation.
Operating levei varies by bar size. (F18)
ln case the brake is not effective. ask
our dealer inspection and repairing. The
engine, if being kept rotated at high speed
with the brake engaged. heats the clutch.
causing a trouble. When the brake is
operated while in operation, immediately
release your fingers form the throttle lever
and keep the engine idling.
STOPPING ENGNIE
1. Release the throttle lever to allow the
engine idling for a few minutes
2. Put the switch to the "O" (stop) Position.
(F1 9 )
(1)Swltch
4iM1W◄
Always follow the safety regulations. The
chain saw must only be used for cutting
wood. lt is forbidden to cut other types of
material. Vibrations and kickback vary with
different materiais and the requirements
of the safety regulations would not be
respected. Do not use the chain saw
as a lever for lifting, moving or splitting
objects. Do not lock it over fixed stands. lt
is forbidden to hitch tools or applications
to the P.t.o. that are not specified by the
manufacturer.
lt is not necessary to force the saw into
the cut. Apply only light pressure while
running the engine at full throttle.
When the saw chain is caught in the cut,
do not attempt to pull it out by force, but
use a wedge or a lever to open the way.
GUARO AGAINST KICKBACK (F21)
This saw is equipped with a chain brake
that will stop the chain in the event of
kickback if operating properly. You must
check the chain brake operation before
each usage by running the saw at full the
throttle for 1.2 seconds and pushing the
front hand guard forward.
The chain should stop immediately with
the engine at full speed. lf the chain is
slow to stop or dose not stop. replace the
brake hand and clutch drum before use.
lt is extremely important that the chain
brake be checked for proper operation
before each use and that the chain be
sharp in order to maintain the kickback
safely lever of this saw. Removal of the
safety devices. lnadequate maintenance.
or incorrect replacement of the bar or
7
Publicidad
