Hikmicro LYNX Serie Instrucciones página 101

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for
an uncontrolled environment.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly
to avoid danger or property loss. Please read all the safety information carefully
before using.
Laws and Regulations
Use of the product must be in strict compliance with the local electrical safety
regulations.
Transportation
Keep the device in original or similar packaging while transporting it.

Keep all wrappers after unpacking them for future use. In case of any failure

occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device

and the company shall not take any responsibilities.
Do not drop the product or subject it to physical shock. Keep the device away

from magnetic interference.
Power Supply
The input voltage for the device should meet the Limited Power Source (5 VDC,

2 A) according to the IEC62368-1 standard. Please refer to actual products and
technical specifications for detailed information.
Make sure the plug is properly connected to the power socket.

DO NOT connect multiple devices to one power adapter, to avoid over-heating

or fire hazards caused by overload.
T
he power source should meet limited power source or PS2 requirements

according to IEC 62368-1 standard.
Battery
The built-in battery type is 18650, and the battery size should be 24 mm × 72

mm. The rated voltage is 3.635 VDC, and the battery capacity is 3350 mAh.
For long-term storage of the battery, make sure it is fully charged every half year

to ensure the battery quality. Otherwise, damage may occur.
CAUTION: Risk of explosion if the battery is replaced by an incorrect type.

Improper replacement of the battery with an incorrect type may defeat a

safeguard (for example, in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or mechanically crush or

cut the battery, which may result in an explosion.
Do not leave the battery in an extremely high temperature surrounding

environment, which may result in an explosion or the leakage of flammable liquid
or gas.
Do not subject the battery to extremely low air pressure, which may result in an

explosion or the leakage of flammable liquid or gas.
Dispose of used batteries according to the instructions.

The built-in battery cannot be dismantled. Please contact the manufacture for

repair if necessary.
DO NOT place the battery in the reach of children.

DO NOT swallow the battery to avoid chemical burns.

Maintenance
If the product does not work properly, please contact your dealer or the nearest

service center. We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.
Wipe the device gently with a clean cloth and a small quantity of ethanol, if

necessary.
If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the device may be impaired.
Clean the lens with soft and dry cloth or wiping paper to avoid scratching it.

Using Environment
Make sure the running environment meets the requirement of the device. The

operating temperature shall be -20 °C to 55 °C (-4 °F to 131 °F), and the operating
humidity shall be from 5% to 95%.
DO NOT expose the device to high electromagnetic radiation or dusty

environments.
DO NOT aim the lens at the sun or any other bright light.

Place the device in a dry and well-ventilated environment.

Avoid equipment installation on vibratory surface or places subject to shock

(neglect may cause equipment damage).
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the power,
unplug the power cable, and contact the service center.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing Subdistrict, Binjiang
District, Hangzhou, Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products might be subject to export
controls in various countries or regions, including without limitation, the United
States, European Union, United Kingdom and/or other member countries of the
Wassenaar Arrangement. Please consult your professional legal or compliance
expert or local government authorities for any necessary export license
requirements if you intend to transfer, export, re-export the thermal series
products between different countries.
Rechtliche Informationen
HAFTUNGSAUSSCHLUSS
DIESE BEDIENUNGSANLEITUNG UND DAS BESCHRIEBENE PRODUKT MIT
SEINER HARDWARE, SOFTWARE UND FIRMWARE WERDEN, SOWEIT
GESETZLICH ZULÄSSIG, IN DER „VORLIEGENDEN FORM" UND MIT „ALLEN
FEHLERN UND IRRTÜMERN" BEREITGESTELLT. HIKMICRO GIBT KEINE
98
Deutsch