Ego Power+ CS2000E Manual página 10

STARTING/STOPPING THE CHAIN SAW
EN
NOTICE:
Before starting the chain saw, check for the oil
level, saw teeth sharpness and properly working kickback
brake paddle. Besides, balanced footing and proper distance
away from the ground are needed.
To Start (Fig. K)
1. Pull the chain-kickback brake paddle towards the front
handle to the operating position (Fig. K).
2. Firmly grasp the front handle with the left hand and the
rear handle with the right hand.
WARNING:
To avoid injury, always use the chain saw
with the right hand grasping the gripping area of the rear
handle (Fig. L).
3. Press and hold the lock-off button with the thumb of
your right hand, then squeeze the trigger switch with
the fingers of your right hand to start the saw (Fig. L).
L-1 Gripping Area
4. Release the lock-off button and continue to squeeze
the trigger switch for continued operation.
5. The further the trigger switch is depressed, the greater
the chain speed. Adjust the speed to suit the task at
hand.
WARNING:
Do not attempt to start the saw when the
saw chain is in a cut.
To Stop
1. Move the chain saw away from cutting area, and
then release the trigger switch to stop the chain saw.
2. Push the chain-kickback brake paddle forward to the
brake position to engage the chain brake (Fig. K).
WARNING:
Always remove the battery pack from the
machine during work breaks and after finishing work.
CHANGING SPEED MODE (FIG. M)
This machine features three speed modes. Each speed mode
the limits the maximum speed of the chain saw. The speed
mode will change with every press of the chain speed button.
The speed bars on the LCD screen will display the active
speed mode: one bar for low speed, two bars for medium
speed, and three bars for high speed. The low speed mode
(ECO) provides better control of the machine and longer
operating time per charge.
M-1 Speed Bars
M-2 Bluetooth Icon
M-3 Headlight Icon
M-4 Brake Icon
10
56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E
NOTE:
only the ECO mode is available. And use of EGO battery pack
rated less than 6.0Ah will not allow you to achieve high
speed. For best performance, we strongly recommend use of
EGO battery packs that are 6.0Ah (e.g., BA3360T) or more.
NOTE:
remember the last speed setting and activate it the next time
the machine is turned on.
NOTE:
pulled or when the speed button or headlight/Bluetooth
button is pressed. It will automatically turn off after
approximately 30 seconds of chain saw inactivity.
LED HEADLIGHT (Fig. N)
The LED headlight is located in the front of the chain saw
housing. The headlight provides illumination for increased
visibility and features 2 brightness levels.
To turn on the headlight, press the headlight/Bluetooth button
(Fig. M) one time. The headlight will turn on in low brightness
level and the low brightness headlight icon will appear on
the LCD screen. Press the headlight/Bluetooth button again
to switch to high brightness level and the high brightness
headlight icon will appear on the LCD screen.
To turn off the headlight, press the headlight/Bluetooth button
the third time and the headlight icon will disappear from the
LCD screen.
OMNI-DIRECTIONAL CHAIN BRAKE SYSTEM (Fig.
O1 and Fig. O2)
is not intended to act as a substitute to the standard/
traditional chain brake. The user should never rely on this
feature during operation of the chain saw to protect against
kickback. Always follow safety instructions related to kickback
mitigation found in the warning section of this manual.
When the omni-directional chain brake system is activated
and stops the saw, the brake icon will be flashing on the LCD
screen (Fig. M). Release the trigger switch, remove the saw
chain and guide bar from the wood, then restart the chain
saw.
M-5 Fuel-gauge Circle
NOTE:
Headlight/
M-6
saw in the plane of the guide bar (fig. O1). The sensors will
Bluetooth Button
not detect any sudden motion of the saw sideways (fig. O2)
(i.e., perpendicular to the plane of the guide bar).
Chain Speed
M-7
Button
When using EGO battery pack rated 2.5Ah or less,
The machine's speed memory function will
The LCD screen lights up when trigger switch is
Low Brightness
N-1 N-3
Headlight Icon
High Brightness
N-2
Headlight Icon
WARNING:
The omni-directional chain brake system
The sensors will only detect sudden motion of the
LED Headlight